Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

1010 Water pump leaks


 
Post new topic    
View previous topic :: View next topic  
Author Message
Ian O
Guest






Report to Moderator

PostPosted: Tue May 01, 2007 1:51 pm    Post subject: 1010 Water pump leaks Reply to specific post Reply with quote

My "63"1010 Crawler water pump leaks out of the front seal. Any idea where to get one and about how much should they cost, I could take it apart and ship it and have it re built for about $150, they say they are short of cores, but this puts me out of service for a week. Must be some new ones out there?


 
Back to top
ralph oregon
Guest






Report to Moderator

PostPosted: Tue May 01, 2007 4:23 pm    Post subject: Re: 1010 Water pump leaks Reply to specific post Reply with quote


gas or diesel?? part # ? ralph

 
Back to top
Roy Suomi
Guest






Report to Moderator

PostPosted: Tue May 01, 2007 4:27 pm    Post subject: Re: 1010 Water pump leaks Reply to specific post Reply with quote

What makes your 1010 so valuable that you can't be without it for a couple of days???Go to a Deere dealer , they can rebuild your old pump..They probably don't have parts in stock for rebuild , but the parts can be ordered..

 
Back to top
jdemaris
Guest






Report to Moderator

PostPosted: Wed May 02, 2007 12:14 pm    Post subject: Re: 1010 Water pump leaks Reply to specific post Reply with quote

1010 water pumps are tougher to rebuild than some other Deere pumps because the castings are so thin. If a guy isn't careful, he can easily break the housing when trying to press the bearing out (I've seen many break).
That being said - if you're careful, and have a press, it's easy to repair. But, you might want to check with possible part's updates.
The original 1010 setup has a seal that rides directly against the cast-iron impeller. So, it used to be necessary to install a new impeller along with the seal. The old impeller will just about always have the seal-face worn out.
But - late 80s - Deere started using a different seal design that retrofits to most older pumps. It is a seal that seals against the bearing shaft and does not need a good impeller. So - if that is now avaialble - all you need is a bearing assembly, a lock clip, and a new seal. With care, it's a 15 minute job to rebuild the pump. But, if the bearing doesn't press easy - heat the housing first or the pump will crack like an egg-shell.

 
Back to top
:   
Post new topic    Yesterday's Tractors Forum Index -> Crawlers, Dozers, Loaders and Backhoes All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters