Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

66 rc governor


 
Post new topic    
View previous topic :: View next topic  
Author Message
leecramsey
Guest






Report to Moderator

PostPosted: Tue May 01, 2007 4:59 pm    Post subject: 66 rc governor Reply to specific post Reply with quote

I am wondering if i need to adjust the governor on my 66. just got it running after sitting outside for 10-15?? years. the throttle lever has very little tension until half way through. I have an all or nothing throttle. I do not have a manual for this machine yet. can i adjust this easily or do i need a manual. any help would be greatly appreciated.

 
Back to top
rrlund
Guest






Report to Moderator

PostPosted: Wed May 02, 2007 5:58 am    Post subject: Re: 66 rc governor Reply to specific post Reply with quote

It doesn't seem too likely that the weights would be stuck. There is a brass washer behind the governor gear that goes bad sometimes,of course you don't know if it was right when it was parked.If you need that washer,it's available from Agco. You'll have to pull the air cleaner to do either,but I'd pull that gov off,just 4 bolts holding it on,then CAREFULLY pull it straight ahead. If everything is OK in there,the spring in the throttle linkage should have 19 coils between the 2 keepers in the inside of it. Unhook the rod that goes from the lever on the side of the gov at the lever. Pull the throttle lever on the steering column all the way down,wide open. Push the linkage to the carb all the way back so the butterfly in the carb is wide open. Now that rod should be ahead of going back in the hole by about 1/3 the width of the rod (toward the radiator). If not,loosten the lock nut at the carb end of it and adjust the turnbuckle until it is. Should get you in business.

 
Back to top
leecramsey
Guest






Report to Moderator

PostPosted: Wed May 02, 2007 4:37 pm    Post subject: Re: 66 rc governor Reply to specific post Reply with quote

thanks for the reply I'll try it this weekend.
Lee

 
Back to top
:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters