Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

2470 remotes not working


 
Post new topic    
View previous topic :: View next topic  
Author Message
Dlblanc
New User


Joined: 13 Apr 2013
Posts: 2


Report to Moderator

PostPosted: Sat Apr 13, 2013 2:14 pm    Post subject: 2470 remotes not working Reply to specific post Reply with quote

I have a case 2470 that steers well and runs through the gears
well. The problem is that it has 4 remotes and they are
sluggish or useless unless I move two of the levers at the
same time. Then they will lift the implement as though there
was no problem. Issue is that I have to let go of the steering
wheel to lift the implement! I would suspect the pump but it
steers well and lifts implements when two levers are engaged
in opposite directions. I would suspect the remote but all four?
I appreciate any suggestions on how to start the
troubleshooting process. Thanks.
 
Back to top
View user's profile
dwag
Long Time User


Joined: 13 Jul 2004
Posts: 1371


Report to Moderator

PostPosted: Sat Apr 13, 2013 5:04 pm    Post subject: Re: 2470 remotes not working Reply to specific post Reply with quote

Implement hoses are hooked up to wrong to couplers.
 
Back to top
View user's profile
Adirondack case guy
Tractor Guru


Joined: 04 Mar 2010
Posts: 17474


Report to Moderator

PostPosted: Sat Apr 13, 2013 5:37 pm    Post subject: Re: 2470 remotes not working Reply to specific post Reply with quote

dwag has it wright. You have the hoses from the lift cylinders coupled to both circuits, rather than each circuit. Switch one coupler in each pair and you should be good to go.
Loren
 
Back to top
View user's profile
jogl
Long Time User


Joined: 22 Jun 2003
Posts: 567
Location: SW Ontario

Report to Moderator

PostPosted: Sun Apr 14, 2013 2:10 am    Post subject: Re: 2470 remotes not working Reply to specific post Reply with quote

Same thing happened to me when I first hooked up to my 2870.

It looks like the remotes should be like this:

W X Y Z
W X Y Z

But they are arranged like this:

W W X X
Y Y Z Z.
 


Last edited by jogl on Sun Apr 14, 2013 2:11 am; edited 1 time in total
Back to top
View user's profile
JMS/.MN
Tractor Guru


Joined: 05 Mar 2009
Posts: 12827


Report to Moderator

PostPosted: Sun Apr 14, 2013 7:20 am    Post subject: Re: 2470 remotes not working Reply to specific post Reply with quote

I had a 2470 for over a decade and always thought that layout was weird. Extremely hard to move the levers as well, so I added an extension to the one I used the most- added about 8 inches to it. makes it easier to find without looking, as well.
 
Back to top
View user's profile
Dlblanc
New User


Joined: 13 Apr 2013
Posts: 2


Report to Moderator

PostPosted: Mon Apr 15, 2013 4:31 pm    Post subject: Re: 2470 remotes not working Reply to specific post Reply with quote

Thanks for the replies. That gives me some confidence. I looked at the plumbing and there was some twine on the linkage and there is a half inch hose between remotes that should probably not be there... I was worried that someone may have used the pump for a continuous flow application and overheated something. You all were right though, I was hooking up the implements to the couplers directly below instead of to the side. It is still around 32 degrees here in Alberta so I dont have anything hooked up to the tractor, I will post a follow up when I confirm in a couple weeks. You all saved me a few more grey hairs, thanks.
 
Back to top
View user's profile
Case Nutty 1660
Tractor Guru


Joined: 08 Mar 2011
Posts: 16904


Report to Moderator

PostPosted: Mon Apr 15, 2013 6:12 pm    Post subject: Re: 2470 remotes not working Reply to specific post Reply with quote

not sure if you will see this but here is my 2670 hooked up correctly

 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters