Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

NewHolland 68 vs 67


 
Post new topic    
View previous topic :: View next topic  
Author Message
JeffK-MN
Regular


Joined: 29 Aug 2002
Posts: 101


Report to Moderator

PostPosted: Sat Jun 16, 2007 8:39 am    Post subject: NewHolland 68 vs 67 Reply to specific post Reply with quote

I just got a New Holland Super hayliner 68 and have been using a New Holland Super hayliner 67.

I"m getting a manual but want to start changing the fluids and greasing it up to use.

Can anyone tell me the difference? I"m using the manual for the 67 and want to try and find all the hidden spots to grease and make sure that it is ready to work.

Tanks Jeff
 
Back to top
View user's profile
RickB
Tractor Guru


Joined: 16 Oct 1998
Posts: 6546


Report to Moderator

PostPosted: Sat Jun 16, 2007 4:37 pm    Post subject: Re: NewHolland 68 vs 67 Reply to specific post Reply with quote

I may be wrong, but I believe the only difference between the S67 and S68 is the tongue length and the extra joint in the PTO shaft on the S68.
 
Back to top
View user's profile
Anonymous
Guest






Report to Moderator

PostPosted: Sat Jun 16, 2007 5:11 pm    Post subject: Re: NewHolland 68 vs 67 Reply to specific post Reply with quote

I had a 67 baler for years. That is a wonderful baler. I think your common sence will tell you where there should be a grease fitting.
 
Back to top
Rexalot
Long Time User


Joined: 02 Jan 2005
Posts: 509


Report to Moderator

PostPosted: Sat Jun 16, 2007 7:17 pm    Post subject: Re: NewHolland 68 vs 67 Reply to specific post Reply with quote

That was my combination until recently, I had the S67 and got a 68.

Obvious stuff, tongue on the 68 attaches to the axle and is longer, PTO shaft on the 68 is also supported by the tongue. Gives it the extra joint.

The 68 has the "wood" plunger bearings vs the S67's rollers.

Same baler. I swapped many parts from my S67 to the 68. I used my S67 parts and owners manual. Servicing is the same.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Implement Alley All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters