Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

CASE CK BACKHOE PIN AND BUSHING


 
Post new topic    
View previous topic :: View next topic  
Author Message
AmeriKen
Regular


Joined: 20 Nov 2004
Posts: 55


Report to Moderator

PostPosted: Sat Jun 16, 2007 5:29 pm    Post subject: CASE CK BACKHOE PIN AND BUSHING Reply to specific post Reply with quote

I'm in the midst of replacing lower pin and bushing on the swing tower of my CASE CK backhoe. As best I can determine it is a model 32 backhoe. Can the pin/bolt, nut, washers, and ball bushing be acquired as a kit or do each part have to be ordered?
Here are the part numbers individually:
Pin: D37451
NUT: 25-1324 (1-1/2" - 12 NF)
SPACERS: D26991
BALL PIVOT BUSHING: D23601

Are these parts available from aftermarket dealers?
 
Back to top
View user's profile
Anonymous
Guest






Report to Moderator

PostPosted: Mon Jun 18, 2007 5:47 am    Post subject: Re: CASE CK BACKHOE PIN AND BUSHING Reply to specific post Reply with quote

About 3/4 of all the pins and bushing are available aftermarket - but a few must come from Case. And those will cost twice what they are worth since Cases knows you cannot get them elsewhere. I just put all new ones in my 32 hoe. Biggest problem was that big self-centering bearing. With mine, the bore in the casting was worn out and egg shaped.
 
Back to top
Anonymous
Guest






Report to Moderator

PostPosted: Mon Jun 18, 2007 6:38 am    Post subject: Re: CASE CK BACKHOE PIN AND BUSHING Reply to specific post Reply with quote

AmeriKen,
The D37451 pin is a part number for the Model #33 hoe. You will probably have to get those parts from Case

jdemaris,
Part of the problem with that lower tower pivot is the D30760 pin on the #32 is not long enough and eats half way through the upper support. If you change to the D37451 pin and special D36476 washer used on the #33 hoe you get full purchase at the upper support. I'd be curious to hear how you repaired the hogged out holes....weld & align bore...bush...or??
 
Back to top
:   
Post new topic    Yesterday's Tractors Forum Index -> Crawlers, Dozers, Loaders and Backhoes All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters