Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

SC starter drive


 
Post new topic    
View previous topic :: View next topic  
Author Message
riverbend
Tractor Expert


Joined: 13 Aug 2003
Posts: 2046
Location: Delano, Minnesota

Report to Moderator

PostPosted: Thu Jul 27, 2017 4:48 pm    Post subject: SC starter drive Reply to specific post Reply with quote

Sometimes the starter on one of my Super Cs will spin without engaging the drive. It is one of the flat spring type. What do you think, lube or just replace it ?

Thanks

Greg
 
Back to top
View user's profile
Janicholson
Tractor Guru


Joined: 30 Jan 2004
Posts: 36397
Location: St. Cloud, MN

Report to Moderator

PostPosted: Thu Jul 27, 2017 5:36 pm    Post subject: Re: SC starter drive Reply to specific post Reply with quote

Clean to bare metal, then Teflon (PTFE) spray. If no joy, replace it with the new style. Sometimes small cables or a bit of corrosion will slow the starter down and it won't snap out to engage. Jim
 
Back to top
View user's profile
riverbend
Tractor Expert


Joined: 13 Aug 2003
Posts: 2046
Location: Delano, Minnesota

Report to Moderator

PostPosted: Fri Jul 28, 2017 1:16 pm    Post subject: Re: SC starter drive Reply to specific post Reply with quote

Hi Jim,

Now that I have the drive in my hand, when the gear spins back on the square thread it jams at the end of the thread. It looks like there is a little groove worn in to the end of the thread and something about that wear is causing it to jam. I'm guessing it is a goner.

Greg
 
Back to top
View user's profile
Janicholson
Tractor Guru


Joined: 30 Jan 2004
Posts: 36397
Location: St. Cloud, MN

Report to Moderator

PostPosted: Fri Jul 28, 2017 2:55 pm    Post subject: Re: SC starter drive Reply to specific post Reply with quote

It could be a snap ring groove and a washer that are missing. (just a guess) The new drives are better and have the drive through spiral splines, no big flat wound spring. Jim
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters