Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

TO-20 ford 9N


 
Post new topic    
View previous topic :: View next topic  
Author Message
cstory
Regular


Joined: 06 May 2008
Posts: 49


Report to Moderator

PostPosted: Tue Nov 14, 2017 6:54 am    Post subject: TO-20 ford 9N Reply to specific post Reply with quote

Will 9N transmission and hydraulic inter change with TO-20. Thanks
 
Back to top
View user's profile
Tom H.
Long Time User


Joined: 24 Feb 2008
Posts: 738


Report to Moderator

PostPosted: Wed Nov 15, 2017 3:22 pm    Post subject: Re: TO-20 ford 9N Reply to specific post Reply with quote

I don't think they will directly. If you have a Ferguson parts book it may show what parts are the same. You can go to the n tractor site and look at their manuals there.
 
Back to top
View user's profile
Bruce(OR)
Tractor Expert


Joined: 10 Apr 2007
Posts: 2343


Report to Moderator

PostPosted: Thu Nov 16, 2017 5:52 pm    Post subject: Re: TO-20 ford 9N Reply to specific post Reply with quote

9N is a 3 speed. Fergy is a 4 speed. It's all different.
 
Back to top
View user's profile
Kirk-NJ
Tractor Guru


Joined: 10 Dec 2006
Posts: 4739


Report to Moderator

PostPosted: Fri Nov 17, 2017 2:31 am    Post subject: Re: TO-20 ford 9N Reply to specific post Reply with quote

Trans from the 9n will not just bolt up to the TO20 engine.
Hydraulics should work in your TO20 from the 9n. Since it was Harry's design the hydraulics are basically the same. Putting the 9n pump in a TO30 may require a little bit of filing.

Kirk
 
Back to top
View user's profile
PackardV8
Regular


Joined: 23 Jan 2011
Posts: 183


Report to Moderator

PostPosted: Fri Nov 17, 2017 2:26 pm    Post subject: Re: TO-20 ford 9N Reply to specific post Reply with quote

9N/TO parts:
I have a situation here where some "mechanic" (note use of quote marks) had replaced the TE20 rear axle bearing retaindner with a 9N bearing retainer.

The TE20 (same as TO20) rear axle bearing retainer is nearly IDENTICLE (i said nearly) to the TE20. It will bolt up just fine but does NOT work because 9N is some 3/16" longer. Which causes excessive axle endplay and therefore tears out the outer axle seals in short order.

And no, don't start telling me about the so-called "Sure Seals". THAT is another whole story in itself that apparently the former "mechanic" (note use of quote marks) tried too.

BOTTOMLINE:
I don't what parts are or are not interchangeable between Ford and Fergy, but better be REAL CAREFUL in trying to do so.
 
Back to top
View user's profile
Bruce(OR)
Tractor Expert


Joined: 10 Apr 2007
Posts: 2343


Report to Moderator

PostPosted: Fri Nov 17, 2017 6:21 pm    Post subject: Re: TO-20 ford 9N Reply to specific post Reply with quote

I think you got the wrong thread on Sure Seals. I did a set on the wife's TO-20 and that was several years ago with no problems
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Harry Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters