Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

383 massey ferguson steering cylinder


 
Post new topic    
View previous topic :: View next topic  
Author Message
swissdairyman
New User


Joined: 12 Nov 2017
Posts: 11


Report to Moderator

PostPosted: Wed Jan 03, 2018 10:42 am    Post subject: 383 massey ferguson steering cylinder Reply to specific post Reply with quote

The tie rods on this tractor should slide in and out of the steering cylinder ends. I wanted to set the axles out on my tractor for better
stability. I cannot get the ends to pull out of the steering cylinder. They are froze up in there. I sent it to massey dealer and they cant
get it out either. They have heated and the whole nine yards. Any suggestion would be appreciated. here is a picture that shows the design.
This is the same set up that i have.
 
Back to top
View user's profile
swissdairyman
New User


Joined: 12 Nov 2017
Posts: 11


Report to Moderator

PostPosted: Wed Jan 03, 2018 10:44 am    Post subject: Re: 383 massey ferguson steering cylinder Reply to specific post Reply with quote





 
Back to top
View user's profile
1989plowboy
New User


Joined: 14 Dec 2017
Posts: 7


Report to Moderator

PostPosted: Fri Jan 05, 2018 8:11 am    Post subject: Re: 383 massey ferguson steering cylinder Reply to specific post Reply with quote

You can try taking the cylinder all the way out and putting some pb blaster in the opening crack on the top and put some constant pressure on pulling both sides it might take. A while though I they are a bear if and when you can get them apart be careful using much heat will take the chrome plateing off the rod
 
Back to top
View user's profile
1989plowboy
New User


Joined: 14 Dec 2017
Posts: 7


Report to Moderator

PostPosted: Fri Jan 05, 2018 8:30 am    Post subject: Re: 383 massey ferguson steering cylinder Reply to specific post Reply with quote

Might could try taking the bolt that does the clamping on each side and losening them and driving it with them loose for a few days iv got 3 of the 300 series Massey?s one seems like it will be stuck indefinitely good luck
 
Back to top
View user's profile
swissdairyman
New User


Joined: 12 Nov 2017
Posts: 11


Report to Moderator

PostPosted: Sat Jan 06, 2018 7:11 am    Post subject: Re: 383 massey ferguson steering cylinder Reply to specific post Reply with quote

That actually seems like a really good idea. I will try that. Thanks!
 
Back to top
View user's profile
1989plowboy
New User


Joined: 14 Dec 2017
Posts: 7


Report to Moderator

PostPosted: Sat Jan 06, 2018 4:36 pm    Post subject: Re: 383 massey ferguson steering cylinder Reply to specific post Reply with quote

Swissdairyman Here?s my email barnyard9009@yahoo .com email me and I?ll send you my phone number I?ll tell you were to look for the other problems you were asking about On your previous thread
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Massey Harris & Massey Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters