Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

58' TO-35 Injection pump help


 
Post new topic    
View previous topic :: View next topic  
Author Message
aprice0101
New User


Joined: 05 Jan 2018
Posts: 6


Report to Moderator

PostPosted: Fri Jan 05, 2018 2:28 pm    Post subject: 58' TO-35 Injection pump help Reply to specific post Reply with quote

Took off the injection pump on my 23c standard diesel to fix fuel leaks. I understand that i need to match the scribe line of the letter "G" up with the cir-clips scribe line with #1 at 19 deg BTC, howeverr, when i get the engine spun there, and insert the 1/4 in rod into the flywheel through the check hole, the pump lines up slightly above "H". The pump, pump shaft and drive gear are all keyed as it can only go in 1 way.....is there something i am missing or something i can do? tractor ran before taking it off by the way. Someone please chime in, i'm relitively frustrated with it right now. Thank you.
 
Back to top
View user's profile
Dieseltech
Tractor Guru


Joined: 29 Feb 2012
Posts: 6466
Location: Indiana

Report to Moderator

PostPosted: Fri Jan 05, 2018 3:03 pm    Post subject: Re: 58' TO-35 Injection pump help Reply to specific post Reply with quote

Put it back on using the flange scribe line. That snap ring may not have been set right in the first place..
 
Back to top
View user's profile
aprice0101
New User


Joined: 05 Jan 2018
Posts: 6


Report to Moderator

PostPosted: Fri Jan 05, 2018 3:11 pm    Post subject: Re: 58' TO-35 Injection pump help Reply to specific post Reply with quote

I'll give it a try in the morning and report back, where exactly will the flange scribe line line up with?
 
Back to top
View user's profile
aprice0101
New User


Joined: 05 Jan 2018
Posts: 6


Report to Moderator

PostPosted: Fri Jan 05, 2018 3:25 pm    Post subject: Re: 58' TO-35 Injection pump help Reply to specific post Reply with quote

Never mind! I found an extremely faint scribe line of the drive gear side flange, also looking at pictures before hand, it seems to copy what you suggested to do, thank you....its about 1/8 in off that scribe line right now.
 
Back to top
View user's profile
aprice0101
New User


Joined: 05 Jan 2018
Posts: 6


Report to Moderator

PostPosted: Fri Jan 05, 2018 3:38 pm    Post subject: Re: 58' TO-35 Injection pump help Reply to specific post Reply with quote

So, just to be sure, since it's a keyed shaft and gear, that portion should be good and within the ""twist" adjustment range which should be close to that scribe line?
 
Back to top
View user's profile
aprice0101
New User


Joined: 05 Jan 2018
Posts: 6


Report to Moderator

PostPosted: Tue Jan 09, 2018 7:44 am    Post subject: Re: 58' TO-35 Injection pump help Reply to specific post Reply with quote

CVPost-Dieseltech wrote:
(quoted from post at 16:03:15 01/05/1Cool Put it back on using the flange scribe line. That snap ring may not have been set right in the first place..

Okay here's an update, put it to the scribe line and it sputtered a bit then blew a bit out the air intake, I haven't touched valves, or front set timing only the cav pump. Tractor was running very good a few days ago before I pulled the cav pump.
 
Back to top
View user's profile
aprice0101
New User


Joined: 05 Jan 2018
Posts: 6


Report to Moderator

PostPosted: Tue Jan 09, 2018 9:25 am    Post subject: Re: 58' TO-35 Injection pump help Reply to specific post Reply with quote

Another update.... Spill tested it, g indeed lines up with the circlip scribe on #1....
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Massey Harris & Massey Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters