Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Hey Welders---Warpage?

Goto page Previous  1, 2

 
Post new topic    
View previous topic :: View next topic  
Author Message
carvel minne farmer
Tractor Expert


Joined: 13 Aug 2017
Posts: 1899
Location: carvel alberta canada

Report to Moderator

PostPosted: Sat Jan 13, 2018 3:23 pm    Post subject: Re: Hey Welders---Warpage? Reply to specific post Reply with quote

good evening big tee, nice job you've done so far on the cutting and fitting, the method I would use to keep everything straight is what I call stich and go, by that I mean you lay each roller out like you have it, tack weld (no more than a 1/4" long tack), keep your heat input on the metal shaft and plates to a minimum. about 3 tacks on each side of each disc plate, tack the 2 end pieces the same, with all the plates in place lay your cross bars at the angle you want, tack them into place, again small tacks, moving from end to end don't work in one area long move from 1 end to the other back to the middle keep it moving don't let any area get hot, it takes more time but saves you a lot of time and headaches trying to straighten heat warped plates and shafts. the key big tee is paitience and keep moving, if you have 2 or three units laid out move from one to the other again keeping the amount of time and heat input to each weld to a minimum.
 
Back to top
View user's profile
4520BW
Tractor Guru


Joined: 05 Aug 2015
Posts: 3769


Report to Moderator

PostPosted: Sat Jan 13, 2018 5:32 pm    Post subject: Re: Hey Welders---Warpage? Reply to specific post Reply with quote

What are you using to build the tool on? I was wondeing if it will be heavy enough. My turbo till is so heavy it dogs the 5095 pulling it down the road. A few years back my neighbor bent a bar on his basket so I cut out the bad spot,maybe 16 inches, and welded in a new bar. The only rod I has was stainless and a 1/4 inch bigger. If you look across the field while it's running you can see the shinny bar.
 
Back to top
View user's profile
big tee
Long Time User


Joined: 10 Jan 2015
Posts: 1343


Report to Moderator

PostPosted: Sat Jan 13, 2018 5:46 pm    Post subject: Re: Hey Welders---Warpage? Reply to specific post Reply with quote

Hi 4520--2 of these, Glencoe 13 shank SS.---Tee

 
Back to top
View user's profile
4520BW
Tractor Guru


Joined: 05 Aug 2015
Posts: 3769


Report to Moderator

PostPosted: Sat Jan 13, 2018 6:35 pm    Post subject: Re: Hey Welders---Warpage? Reply to specific post Reply with quote

So how wide you making it?
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Talk All times are GMT - 8 Hours
Goto page Previous  1, 2
Page 2 of 2

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters