Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

more D-19 questions


 
Post new topic    
View previous topic :: View next topic  
Author Message
Al Baker(pumpman)
Long Time User


Joined: 29 Nov 2014
Posts: 645


Report to Moderator

PostPosted: Sun Feb 04, 2018 1:12 pm    Post subject: more D-19 questions Reply to specific post Reply with quote

I have an engine from a 200 allis in my D-19. If I had 20.8x38
tires, and the engine turning 2600 RPMs what road speed do you think I would get. Would this tractor be fast enough to work well on a poop spreader hauling 5-6 miles each way? Al
 
Back to top
View user's profile
DrAllis
Long Time User


Joined: 18 Jan 2015
Posts: 828


Report to Moderator

PostPosted: Sun Feb 04, 2018 2:07 pm    Post subject: Re: more D-19 questions Reply to specific post Reply with quote

A 20.8 x 38 is 72 inches tall while an 18.4 x 34 is 65 inches tall. That takes 14.4 MPH @ 2000 RPM to 15.9 MPH just in tire diameter difference. Now, increase 2000 RPM to 2600 RPM and you'd have 22.08 MPH. This should be pretty close. It ain't a Farmall, but it's still pretty fast. How'd you get that 301 engine to fit beside the power steering ram ???
 
Back to top
View user's profile
Al Baker(pumpman)
Long Time User


Joined: 29 Nov 2014
Posts: 645


Report to Moderator

PostPosted: Sun Feb 04, 2018 4:46 pm    Post subject: Re: more D-19 questions Reply to specific post Reply with quote

What I did was built what I felt was the best of both worlds. The engine from a 190/200 Allis was one of, if not the best Allis ever built. The hand operated power director from the D series was bomb proof. So I installed the 2900 engine in the D-19 with very little work. I used the 190 axle with the steering cylinder and Charlynn steering motor. 190 live Hydraulic pump and 3pt. I did have to have a custom radiator built. Only big job was building a new front radiator support/front axle support. Tractor was my Granddad's and I grew up in the seat. Was a gas tractor and I never missed lunch using it. I had to head to the house at noon for more fuel. I bought the 19 from my uncle few years after Grandpa died. I couldnt find a good 262 diesel to bolt in so I started on the big swap. I would like to have a purpose for this tractor when I pull it out of the shop. Cutting or raking hay is the only jobs that I have for it. If I could haul poop with it in warm months she would have a important job to fill. Think I will have to hunt up a 7000 with power adjust rims and centers being parted out. Al
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters