Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

62 881D


 
Post new topic    
View previous topic :: View next topic  
Author Message
Destroked 450
Tractor Guru


Joined: 31 Mar 2016
Posts: 4270
Location: Harned, Ky.

Report to Moderator

PostPosted: Wed Feb 07, 2018 2:44 pm    Post subject: 62 881D Reply to specific post Reply with quote

Finally able to upload photos again.
Here's some photos I took a while back of the 62 881D I found a few years ago that had been sitting in a barn for over 20 years.
I had washed in off but it still needs a good cleaning.

Notice the power adjust wheels and spacers
The little white sticker on the side of tire says 2-92, thinking thats went they were made.

Doesn't show in the photo but the fuel tanks been replaced.
Had to replace the rubber hose on the power steering line.
Has the wrong lower radiator hose.
Engine block number

Original bumper had been replaced with a cheesy aftermarket so I took it off.

Starters been replaced and I had to replace the bendix just before the photo's where taken
Pre cleaner pipe's been repaired, bracket doesn't line up with the starter bolts like it should

Some of the labels aren't readable but their still there.

Still has the original over running clutch transmission
Rest-o-ride seat still sits pretty level
Plough light, grease gun holder, has 601 picker brackets under the axles.
Does anyone know if the tractors originally came with rubber bushings between the fender and axle, these are the first I've ever seen.
Haven't been able to find much info on this remote valve ether.
There's gold in them parts!
Is it possible they where still installing parts from the Gold Demonstrators on SOS trans in 62
 
Back to top
View user's profile
Royse
Tractor Guru


Joined: 17 Jan 2011
Posts: 17222
Location: Ionia County Michigan

Report to Moderator

PostPosted: Wed Feb 07, 2018 3:21 pm    Post subject: Re: 62 881D Reply to specific post Reply with quote

That's a great looking tractor. Pretty straight for the age.
Your hydraulic valve looks very similar to the one that came
on my 851. Mine is a NAA valve with an adapter plate to fit
the x00/x01/x000 tractors. More valuable as an NAA valve
because they are harder to find. The handle on mine could be
installed from either side and was setup so it went out to the
right hand side of the seat. Nice, because I didn't kick it that way.






 
Back to top
View user's profile
johnofnewhaven
Long Time User


Joined: 30 Sep 2016
Posts: 942


Report to Moderator

PostPosted: Wed Feb 07, 2018 4:08 pm    Post subject: Re: 62 881D Reply to specific post Reply with quote

Very nice Destroked. My neighbor has
some select o speed Ford in his barn.
He had it out once that I saw. The
trans does not shift right. He said he
would sell it to me but I never gave it
a second thought because of the trans.
 
Back to top
View user's profile
Dollar Bill
Long Time User


Joined: 01 May 2008
Posts: 1174
Location: Keystone Heights, FL

Report to Moderator

PostPosted: Thu Feb 08, 2018 12:00 am    Post subject: Re: 62 881D Reply to specific post Reply with quote

Awesome find and a tip of the brim to the previous caretaker - Rare to find one so well cared for!!
 
Back to top
View user's profile
Destroked 450
Tractor Guru


Joined: 31 Mar 2016
Posts: 4270
Location: Harned, Ky.

Report to Moderator

PostPosted: Thu Feb 08, 2018 7:43 am    Post subject: Re: 62 881D Reply to specific post Reply with quote


Thanks.
I like that handle, never seen one before
 
Back to top
View user's profile
Destroked 450
Tractor Guru


Joined: 31 Mar 2016
Posts: 4270
Location: Harned, Ky.

Report to Moderator

PostPosted: Thu Feb 08, 2018 8:45 am    Post subject: Re: 62 881D Reply to specific post Reply with quote


After posting the photo's I realized I had a better photo of the rubber washers between the fenders and axle housing.
You can also see the blue picker bracket as well


Any one know if the rubber washers are factory?
Nothing in parts search for a 801 but 63/ 4000 calls for a 3/16 spacer between the fender and axle, doesn't say if it's rubber or steel.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Ford All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters