Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Using epoxy metal

Goto page Previous  1, 2

 
Post new topic    
View previous topic :: View next topic  
Author Message
Texasmark1
Tractor Guru


Joined: 22 Nov 2011
Posts: 8314


Report to Moderator

PostPosted: Mon Feb 12, 2018 4:27 pm    Post subject: Re: Using epoxy metal Reply to specific post Reply with quote

JB Weld is popular here. Ensure you mix it 50-50 and give it plenty of time to cure out. Grind it off, drill and tap and be on your way. for holes, or finish off with an end mill.
 
Back to top
View user's profile
Janicholson
Tractor Guru


Joined: 30 Jan 2004
Posts: 29881
Location: St. Cloud, MN

Report to Moderator

PostPosted: Mon Feb 12, 2018 7:21 pm    Post subject: Re: Using epoxy metal Reply to specific post Reply with quote

Well Implied. Jim
 
Back to top
View user's profile
Dick L
Tractor Guru


Joined: 01 Sep 1999
Posts: 12840
Location: Edon Ohio

Report to Moderator

PostPosted: Tue Feb 13, 2018 4:58 am    Post subject: Re: Using epoxy metal Reply to specific post Reply with quote

Because I was wanting to use the product on an injection mold they sent in a tec fellow. He helped with the repair and it only lasted a week. I machined the cured product with a standard mill cutter and finished up with fine sand strip.
 
Back to top
View user's profile
circus
Long Time User


Joined: 22 Feb 2010
Posts: 715


Report to Moderator

PostPosted: Tue Feb 13, 2018 8:51 am    Post subject: Re: Using epoxy metal Reply to specific post Reply with quote

Maybe a autobody aluminized polyester filler would work. Metal-to-metal or all-metal comes to mind. As long as you don't use it on a high temperature bearing it should work. Sets in 10 minutes. Surfaces must be clean,oil free and scuffed.

 
Back to top
View user's profile
fixerupper
Tractor Guru


Joined: 12 Oct 2003
Posts: 16006
Location: Albert City Iowa

Report to Moderator

PostPosted: Tue Feb 13, 2018 5:12 pm    Post subject: Re: Using epoxy metal Reply to specific post Reply with quote

I used JB weld to fit a new bushing in a walleyed out bore where the front axle pivots on a 1086 IH. Several thousand hours later I replaced the bushing again just to tighten things up. The old JB ‘d bushing was holding just fine. When I pounded it out I had forgotten I had used JB the first time and I wondered what that gray stuff was till the light bulb lit up in my head.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Tool Talk All times are GMT - 8 Hours
Goto page Previous  1, 2
Page 2 of 2

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters