Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Another dilemma? Pulley Diameter?


 
Post new topic    
View previous topic :: View next topic  
Author Message
John Saeli
Tractor Guru


Joined: 19 Dec 2009
Posts: 3574


Report to Moderator

PostPosted: Thu Mar 08, 2018 11:37 am    Post subject: Another dilemma? Pulley Diameter? Reply to specific post Reply with quote

What is the correct outside diameter of the generator pulley for the 430 530 & 630 tractors where the Tach drive was on the generator?
 
Back to top
View user's profile
casecollectorsc
Tractor Guru


Joined: 24 Dec 2011
Posts: 6089


Report to Moderator

PostPosted: Thu Mar 08, 2018 5:00 pm    Post subject: Re: Another dilemma? Pulley Diameter? Reply to specific post Reply with quote

Kind of a sob to measure when on the tractor. 3 1/4" is as close as I get for the one on my 630.
 
Back to top
View user's profile
Adirondack case guy
Tractor Guru


Joined: 04 Mar 2010
Posts: 14028


Report to Moderator

PostPosted: Thu Mar 08, 2018 5:00 pm    Post subject: Re: Another dilemma? Pulley Diameter? Reply to specific post Reply with quote

John, I will measure my 431T in the morning and give you a jingle on the phone. I need to order a complete tach cable housing and core for this tractor.
Loren
 
Back to top
View user's profile
casecollectorsc
Tractor Guru


Joined: 24 Dec 2011
Posts: 6089


Report to Moderator

PostPosted: Fri Mar 09, 2018 3:55 pm    Post subject: Re: Another dilemma? Pulley Diameter? Reply to specific post Reply with quote

Sooo, how close was I at 3 1/4" for pulley size? Kinda hard to get a measurement of the pulley while on the tractor.
 
Back to top
View user's profile
Don Rudolph
Tractor Expert


Joined: 29 Aug 2010
Posts: 3180


Report to Moderator

PostPosted: Fri Mar 09, 2018 5:06 pm    Post subject: Re: Another dilemma? Pulley Diameter? Reply to specific post Reply with quote

John,

The pulley on our 1969 430 with generator and tach drive measures 3 1/2" outside diameter. So Steve is very close. Don
 
Back to top
View user's profile
John Saeli
Tractor Guru


Joined: 19 Dec 2009
Posts: 3574


Report to Moderator

PostPosted: Fri Mar 09, 2018 6:39 pm    Post subject: Re: Another dilemma? Pulley Diameter? Reply to specific post Reply with quote

Thanks everybody!!
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters