Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

C-301 in a 560


 
Post new topic    
View previous topic :: View next topic  
Author Message
feverpuller
Regular


Joined: 23 Mar 2018
Posts: 100


Report to Moderator

PostPosted: Sat Apr 14, 2018 5:05 pm    Post subject: C-301 in a 560 Reply to specific post Reply with quote

Ok guys I may have asked before but here it goes again. What all needs to be done to install a c-301 into a 560 gas. I know the exhaust is different and doesn't exhaust vertically. Is it pretty much a drop in and go or do I need to do some modifying? Thanks
 
Back to top
View user's profile
Lee460
Regular


Joined: 27 Sep 2014
Posts: 93


Report to Moderator

PostPosted: Sun Apr 15, 2018 11:36 am    Post subject: Re: C-301 in a 560 Reply to specific post Reply with quote

No modifying, just a lot of wrenching. Change front cover and adapter plate, oil filter assembly, oil pump pick up tube, oil pan, governor, oil fill tube and dip stick, rear adapter plate, fly wheel, pressure plate, clutch, water pump and all pulleys. To remove the front adapter plate you need to pull the cam, so you have to pull the lifters, push rods, and oil pump. I think that is all. When done, at stock 560 rpm, you will have about 75-78 hp if you do nothing else to it. Plus a big pile of scrape iron left over.(lol) I have done 3 or 4, doesn't take to long, depends on how much beer is consumed.
 
Back to top
View user's profile
feverpuller
Regular


Joined: 23 Mar 2018
Posts: 100


Report to Moderator

PostPosted: Sun Apr 15, 2018 6:59 pm    Post subject: Re: C-301 in a 560 Reply to specific post Reply with quote

Thank you sir
 
Back to top
View user's profile
feverpuller
Regular


Joined: 23 Mar 2018
Posts: 100


Report to Moderator

PostPosted: Thu Jun 21, 2018 11:00 am    Post subject: Re: C-301 in a 560 Reply to specific post Reply with quote

Does the rear cover take a gasket? What all gaskets will I need to do the swap and where the best place to get them. I'm in Indiana
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Pulling All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters