Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Grading questions


 
Post new topic    
View previous topic :: View next topic  
Author Message
S854
Regular


Joined: 08 Feb 2018
Posts: 23


Report to Moderator

PostPosted: Tue Apr 03, 2018 1:45 pm    Post subject: Grading questions Reply to specific post Reply with quote

I'm picking up a box scraper on Thursday to (hopefully) smooth out the driveway/garage apron.

I've been having a ball plowing snow with the front blade... but in the meantime I've also scrapped quite a bit of the gravel drive into the snow piles... gonna need to reposition the gravel and get a crown on the drive... I'm gonna have a shallow ditch on each side of the drive.

Here's a rough sketch of what I have to work on (arrows show the direction the water needs to flow)... the drive being about 1/4 mile long and running gently downhill.

I need to get the barn and garage to drain downhill (along with the short section of drive between them) then get the road to drain to each side. Right now I have relatively flat spots where water pools in front of the barn and also on the road.



The crown of the road seems simple enough (tilt the blade to get the gravel back to the center then flatten the top of the crown?)...

It's the barn/garage part I'm not so sure of... do I run the tractor west/east to bring some material back towards the garage then go east/west to smooth it out?

The short section of drive between the barn and the garage... same thing?

Any input from those who've done something similar in the past?
 
Back to top
View user's profile
VicS
Tractor Guru


Joined: 12 Mar 2010
Posts: 4523


Report to Moderator

PostPosted: Sat May 05, 2018 11:19 am    Post subject: Re: Grading questions Reply to specific post Reply with quote

The way I use a box blade is this, let
right hitch arm down about a inch or so at
ball end. Set teeth so when blade is level
front to rear just touch or barely clear
ground when blade is down. Then shorten top
link so teeth dig, maybe as short as it
will go. Then work entire driveway,driving
on right side. Maybe 4 rounds. Then extend
top link till box blade is higher in front
than back. Work this way carring almost a
full blade full. Making a few rounds. You
will have put crown in your drive by now.
If to much raise right link a little. I
have a cylinder on the top link so i
lengthen it on the go to lose gravel in the
low places. Also set your 3 point lever
just a little lower than you are blading.
Clear as mud! But I hope it helps.
Oh works best if a little wet. But not muddy.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Using Your Tractor & Crop Talk All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters