Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Farmhand f11


 
Post new topic    
View previous topic :: View next topic  
Author Message
SVcummins
Tractor Guru


Joined: 06 Feb 2017
Posts: 4881


Report to Moderator

PostPosted: Sat May 05, 2018 8:28 am    Post subject: Farmhand f11 Reply to specific post Reply with quote

Finally starting on the loader project I pulled it off last January and I?m just finally getting around to pulling it all apart so I can start cleaning it up and reseal the cylinders


 
Back to top
View user's profile
SVcummins
Tractor Guru


Joined: 06 Feb 2017
Posts: 4881


Report to Moderator

PostPosted: Mon May 14, 2018 8:04 pm    Post subject: Re: Farmhand f11 Reply to specific post Reply with quote

..

 
Back to top
View user's profile
ArleninOr
Tractor Expert


Joined: 04 Jan 2008
Posts: 1913


Report to Moderator

PostPosted: Mon May 14, 2018 9:51 pm    Post subject: Re: Farmhand f11 Reply to specific post Reply with quote

Looking good. Did you get the cylinders resealed yet?
 
Back to top
View user's profile
SVcummins
Tractor Guru


Joined: 06 Feb 2017
Posts: 4881


Report to Moderator

PostPosted: Mon May 14, 2018 10:30 pm    Post subject: Re: Farmhand f11 Reply to specific post Reply with quote

Thank . And NopeI haven?t had time to get out of town to get the seal Kits yet . Might end up getting them from Baum hydraulics as that?s where my guy gets em and then marks the price up .
 
Back to top
View user's profile
SVcummins
Tractor Guru


Joined: 06 Feb 2017
Posts: 4881


Report to Moderator

PostPosted: Wed May 16, 2018 6:39 pm    Post subject: Re: Farmhand f11 Reply to specific post Reply with quote

Going to take a load of parts to town to wash then get the cylinders resealed . My nephew is coming in the next day or two and we?ll sand the primer and shoot the color . Going to have the local welding shop build me a new bucket to replace the old bent farmhand quick coupler

 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Paint and Bodywork All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters