Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

ampli torch stuck in high


 
Post new topic    
View previous topic :: View next topic  
Author Message
minne hopeless
New User


Joined: 27 May 2018
Posts: 3


Report to Moderator

PostPosted: Sun May 27, 2018 4:54 pm    Post subject: ampli torch stuck in high Reply to specific post Reply with quote

maybe someone has seen this before? my super u-302 had a noise in drive line, after opening transmission ampli torch and spring clutch decided to replace sprag clutch and hub, replace clutch and pressure plate, and close gearbox back up. have tractor runnign again, but has a wine when clutch is out (don't remember that before this work) and seems to be stuck in high side of ampli torch, does change speed when lever is pulled back to low. I'm sure I did something or didn't do what should of, wondering where I might start
 
Back to top
View user's profile
ChrisQ
Regular


Joined: 05 Nov 2012
Posts: 263
Location: Jordan, MN

Report to Moderator

PostPosted: Sun May 27, 2018 6:03 pm    Post subject: Re: ampli torch stuck in high Reply to specific post Reply with quote

Split it and shim the front cover for the ampli-torc compartment correctly. I did this on my Jetstar 3 Super, had to mash on the brakes to get it to go to low, let off the brakes, and it it went back to high. Kinda wierd. Never gave it a thought to re shim when I put it back together after putting new bearings in the transmission.
 
Back to top
View user's profile
minne hopeless
New User


Joined: 27 May 2018
Posts: 3


Report to Moderator

PostPosted: Sun May 27, 2018 6:33 pm    Post subject: Re: ampli torch stuck in high Reply to specific post Reply with quote

the front cover? ok (I used two new yellow shims the thicker ones instead of the one yellow and two blue old shims that were in there) I can try more... how does one determin how many or how far to shim? (to bad these old yellow tractor parts are all special order and wait for mailman HAHA)
 
Back to top
View user's profile
ChrisQ
Regular


Joined: 05 Nov 2012
Posts: 263
Location: Jordan, MN

Report to Moderator

PostPosted: Sun May 27, 2018 7:02 pm    Post subject: Re: ampli torch stuck in high Reply to specific post Reply with quote

Get an I&T manual for it. There is an end play spec. You check it with a dial indicator.
 
Back to top
View user's profile
minne hopeless
New User


Joined: 27 May 2018
Posts: 3


Report to Moderator

PostPosted: Sun May 27, 2018 7:39 pm    Post subject: Re: ampli torch stuck in high Reply to specific post Reply with quote

I was afraid you'd say that, I got the book but not the dail indicator.
But thanks alot this gives me the right direction.
 
Back to top
View user's profile
ChrisQ
Regular


Joined: 05 Nov 2012
Posts: 263
Location: Jordan, MN

Report to Moderator

PostPosted: Mon May 28, 2018 3:45 pm    Post subject: Re: ampli torch stuck in high Reply to specific post Reply with quote

Get a magnetic mount for the indicator. They are not real expensive. It doesn't need to be anything fancy. After having it you will find other uses for it.
 
Back to top
View user's profile
Alan K
Tractor Guru


Joined: 09 May 1999
Posts: 6323


Report to Moderator

PostPosted: Sat Jun 09, 2018 12:49 pm    Post subject: Re: ampli torch stuck in high Reply to specific post Reply with quote

Ive heard it is better to have a little extra endplay than not enough. That
might be why you are having trouble. I have an M5 to finish yet.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Minneapolis Moline All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters