Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

TR98 NH COMBINE CHAFF SPREADER INSTALL

Goto page Previous  1, 2

 
Post new topic    
View previous topic :: View next topic  
Author Message
Milk
Regular


Joined: 12 Nov 2016
Posts: 65


Report to Moderator

PostPosted: Tue Aug 14, 2018 4:19 am    Post subject: Re: TR98 NH COMBINE CHAFF SPREADER INSTALL Reply to specific post Reply with quote

Thanks for the advice I got the chaff
spreader hooked up yesterday. Seems to work
the way that its supposed to. All is well
so far!!
 
Back to top
View user's profile
dbock
Regular


Joined: 21 Aug 2002
Posts: 299


Report to Moderator

PostPosted: Wed Sep 12, 2018 2:32 pm    Post subject: Re: TR98 NH COMBINE CHAFF SPREADER INSTALL Reply to specific post Reply with quote

Milk, did you get your beater replaced? We are having a hard time getting ours out. I have some questions if you have gotten yours out.
 
Back to top
View user's profile
Milk
Regular


Joined: 12 Nov 2016
Posts: 65


Report to Moderator

PostPosted: Wed Sep 12, 2018 6:42 pm    Post subject: Re: TR98 NH COMBINE CHAFF SPREADER INSTALL Reply to specific post Reply with quote

so sorry for the late reply. what I did was to bolt on to the discharge beater fins 4" pieces of notched metal,4 of them for each fin,they have to be balanced equally.I staggered each 4" notched piece so as when the beater fins make a revolution, they have more grabbing power to pull the material coming out of the rotors. Haven't used it yet but I think that it's going to work!! I looked at the beater and decided that there was too much stuff to dissemble, way too much work!!! I got this idea from looking at the website from the company in south Dakota that specializes in retrofitting replacement parts for different makes of combines.
 
Back to top
View user's profile
dbock
Regular


Joined: 21 Aug 2002
Posts: 299


Report to Moderator

PostPosted: Sat Sep 15, 2018 4:13 am    Post subject: Re: TR98 NH COMBINE CHAFF SPREADER INSTALL Reply to specific post Reply with quote

Thanks for the reply. After a lot of heat and a few choice words, we finally got the beater out. I wasn't sure how the beater attached to the shaft, but the shaft has a tapered spline on one end. Our beater was to beat up to repair, so we are going with the the one from ND. We had to send them the hubs off of our beater, so it will be 10 days before we get it.
 
Back to top
View user's profile
Milk
Regular


Joined: 12 Nov 2016
Posts: 65


Report to Moderator

PostPosted: Sat Sep 15, 2018 10:40 am    Post subject: Re: TR98 NH COMBINE CHAFF SPREADER INSTALL Reply to specific post Reply with quote

That's great!looks like a great retrofit. Are you changing out the bearings also?Its a little too spendy for me but I think that it's going to be better than new!
I got the chaff spreader working great but the reel turns over very slowly, can't make it go any faster than a slow turn!!Any suggestions are greatly appreciated!!
 
Back to top
View user's profile
Milk
Regular


Joined: 12 Nov 2016
Posts: 65


Report to Moderator

PostPosted: Sat Sep 15, 2018 11:41 am    Post subject: Re: TR98 NH COMBINE CHAFF SPREADER INSTALL Reply to specific post Reply with quote

Does anyone here on this forum have any suggestions on how to get the reel to turn on my TR98 NH combine? Last year it was would slow down and stop for no apparent reason! the control knob in the cab just spins without feeling any pressure when turning it, not much control for the reel, but some control is there!
Only thing different I did this year was to add a chaff spreader!The machine already has a binfil extender! Maybe too many hydraulic hookups for reel pump!!!!
 
Back to top
View user's profile
dbock
Regular


Joined: 21 Aug 2002
Posts: 299


Report to Moderator

PostPosted: Sat Sep 15, 2018 4:53 pm    Post subject: Re: TR98 NH COMBINE CHAFF SPREADER INSTALL Reply to specific post Reply with quote

Are the bin extension auger and the chaff spreader turning alright? If the system was overloaded then it would probably slip the belt that drives the reel pump on the right side of the combine. You might check to see if that belt is tight. It might also be in the valve or the reel speed controller. I think there is a way to set the valve manually, but I'm not sure how.
 
Back to top
View user's profile
Milk
Regular


Joined: 12 Nov 2016
Posts: 65


Report to Moderator

PostPosted: Sat Sep 15, 2018 7:04 pm    Post subject: Re: TR98 NH COMBINE CHAFF SPREADER INSTALL Reply to specific post Reply with quote

everything turns at valved controlled speeds. Not much pressure on the port where the hydraulic hook for the reel speed hydraulic is located. Tried adjusting the valve to override the cab controller located under the platform, but can't seem to move it after loosen the nut! might have to call in the mechanic!!
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Combines and Harvesters All times are GMT - 8 Hours
Goto page Previous  1, 2
Page 2 of 2

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters