Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

TO 35 HYDRAULIC PROBLEM


 
Post new topic    
View previous topic :: View next topic  
Author Message
ZangFarms
Regular


Joined: 13 Jan 2017
Posts: 20


Report to Moderator

PostPosted: Sat Oct 06, 2018 11:13 am    Post subject: TO 35 HYDRAULIC PROBLEM Reply to specific post Reply with quote

I'm working on a Ferguson TO35. I'm currently having a issue
with the hydraulic system and the 3pt. the owner complained
of the three point being slow to raise with a load on it. a
pressure check showed the pump was only making 1000-
12oo psi. the pump was worn out beyond specs so I replaced
the cam, cam blocks, and all new O-rings where required. I
now have 2000psi which is what is spec'd for that hydraulic
system. the problem I am having is that now when I start the
tractor regardless of the position of the draft or position control
the 3pt raises to the fully raised position and will not lower
while the tractor is running. I also made all of the other
necessary control linkage adjustments as per the service
manual. what could be the cause of this problem? I am
absolutely stumped.
any help is greatly appreciated. thanks.
 
Back to top
View user's profile
Steve@Advance
Tractor Guru


Joined: 12 Nov 2013
Posts: 11419


Report to Moderator

PostPosted: Sat Oct 06, 2018 2:52 pm    Post subject: Re: TO 35 HYDRAULIC PROBLEM Reply to specific post Reply with quote

Open the right round cover, push the control lever off to the side of the roller, see if you can control the lift manually.

There is an adjustment nut down below the roller arm. Be very careful, don't reach down there with it running!

The adjustment is very sensitive, the arms from the control levers don't move very far. It may take several attempts to get it right.
 
Back to top
View user's profile
Dieseltech
Tractor Guru


Joined: 29 Feb 2012
Posts: 6168
Location: Indiana

Report to Moderator

PostPosted: Sat Oct 06, 2018 3:47 pm    Post subject: Re: TO 35 HYDRAULIC PROBLEM Reply to specific post Reply with quote

What Steve said, adjustments are off somewhere. Most likely the pump rocker lever adjusting self locking nut. There are marks on the quadrant, best get the service manual out and follow the lift cover/pump synchronization adjustments.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Harry Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters