Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

ID an AC plow?


 
Post new topic    
View previous topic :: View next topic  
Author Message
jCarroll
Long Time User


Joined: 12 Jan 2000
Posts: 1158


Report to Moderator

PostPosted: Tue Oct 02, 2018 8:43 am    Post subject: ID an AC plow? Reply to specific post Reply with quote


I recently acquired a 3-14 semi-mounted moldboard plow.
The remaining paint is AC orange, and it has the long, hitch loop so I assume it's an AC.
But can someone confirm, and maybe put a model number on it?

309244 is stamped on the back of each moldboard.
NO. 124-14 RH is stenciled on the back of each moldboard.
332810 is the casting number on the coulter hub which has the zerk.

Thx for your help.

(Sorry I don't know how to post photos)
 
Back to top
View user's profile
Skyhighballoon(MO)
Regular


Joined: 06 Jul 2007
Posts: 482
Location: Pilot Grove, MO

Report to Moderator

PostPosted: Tue Oct 02, 2018 11:13 am    Post subject: Re: ID an AC plow? Reply to specific post Reply with quote

Are the shanks vertical (not slanted forward) for the bottoms? If so and with the much older 124 bottoms, it's very likely to be a Model 53 plow, sometimes known as a WD pickup plow. Finding replacement shares/shins that bolt right up will be next to impossible for those 124 bottoms. About the only thing left available wear parts wise for Allis plows is for the much newer 387 bottoms. You might be able to re-drill your frogs for another share that is close to yours. Mike
 
Back to top
View user's profile
BushogPapa
Tractor Guru


Joined: 26 Dec 2001
Posts: 7911


Report to Moderator

PostPosted: Mon Oct 08, 2018 6:34 am    Post subject: Re: ID an AC plow? Reply to specific post Reply with quote


If it has a long "Hitch Loop, I think that says it is for a later "Snap- Coupler"..(WD-45?).

Otherwise it will have the old cross-pin Hitch that nobody should use..(Convert it)..!!
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters