Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

9n dash cable


 
Post new topic    
View previous topic :: View next topic  
Author Message
Old560
Regular


Joined: 11 Dec 2015
Posts: 175


Report to Moderator

PostPosted: Tue Oct 09, 2018 12:27 pm    Post subject: 9n dash cable Reply to specific post Reply with quote

Trying to help my neighbor out her husband passed away she?s been using His 9n to clean up a little bit. Yesterday couldn?t get the tractor to move or the PTO to work. There?s a little knob on the dash with a cable that goes into the transmission/bell housing. once I pushed the knob in everything worked fine what does that cable do? what is it for?
 
Back to top
View user's profile
Royse
Tractor Guru


Joined: 17 Jan 2011
Posts: 16594
Location: Ionia County Michigan

Report to Moderator

PostPosted: Tue Oct 09, 2018 3:34 pm    Post subject: Re: 9n dash cable Reply to specific post Reply with quote

Sounds like the shift knob for a Sherman step-up cable operated
transmission. Others a lever operated. Most of the cables are
froze up after years of not being used, so she's lucky.
 
Back to top
View user's profile
Kirk-NJ
Tractor Guru


Joined: 10 Dec 2006
Posts: 4762


Report to Moderator

PostPosted: Wed Oct 10, 2018 1:43 am    Post subject: Re: 9n dash cable Reply to specific post Reply with quote

As Royse said it's for a sherman shep up or step down trans. It's likely it wasn't pull out enough and you were in the neutral detent. Pushing the knob in engages the sherman in the step up (speeds the tractor up) or step down (slows the tractor down) depending on which sherman you have. To engage your standard gears the knob should be pulled out. The clutch pedal should be depressed when engaging or disengaging the sherman. If when pulled out it will not go passed the neutral detent Then lubricate the cable and gently work it in or out. Keep the cable well lubricated to ensure it works properly. here is a video on the cable sherman
sherman link

 
Back to top
View user's profile
Old560
Regular


Joined: 11 Dec 2015
Posts: 175


Report to Moderator

PostPosted: Wed Oct 10, 2018 1:09 pm    Post subject: Re: 9n dash cable Reply to specific post Reply with quote

Thanks for the replies that explains it
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Ford All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters