Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Allis Chalmers G creeper gear failure


 
Post new topic    
View previous topic :: View next topic  
Author Message
neilpoulson
New User


Joined: 27 Oct 2018
Posts: 2


Report to Moderator

PostPosted: Sat Oct 27, 2018 12:01 pm    Post subject: Allis Chalmers G creeper gear failure Reply to specific post Reply with quote

Three times I have lost my creeper gear. Each time I found that the shifter rod had moved past the neutral position. I then took the tractor apart and realigned the shifter to regain the use of the creeper gear. Does anyone know why this happens and what I can do to fix it?
Thanks to anyone for your help
Neil
 
Back to top
View user's profile
JoeM(GA)
Tractor Expert


Joined: 31 Aug 2007
Posts: 1626


Report to Moderator

PostPosted: Sat Oct 27, 2018 12:11 pm    Post subject: Re: Allis Chalmers G creeper gear failure Reply to specific post Reply with quote

Usually a worn shift lever end and/or the mating notch on the shift rail is worn.
 
Back to top
View user's profile
Mike(NEOhio)
Tractor Guru


Joined: 12 May 2013
Posts: 3853
Location: Geauga County, Ohio

Report to Moderator

PostPosted: Sat Oct 27, 2018 2:51 pm    Post subject: Re: Allis Chalmers G creeper gear failure Reply to specific post Reply with quote

It's a little tricky to keep those two keys in place while you insert the shift lever. Are you sure one isn't dropping out? If OK then it's just wear.
 
Back to top
View user's profile
Dick L
Tractor Guru


Joined: 01 Sep 1999
Posts: 12871
Location: Edon Ohio

Report to Moderator

PostPosted: Sun Oct 28, 2018 5:51 am    Post subject: Re: Allis Chalmers G creeper gear failure Reply to specific post Reply with quote

What keys are you talking about? I don't recall any keys.


 
Back to top
View user's profile
JoeM(GA)
Tractor Expert


Joined: 31 Aug 2007
Posts: 1626


Report to Moderator

PostPosted: Sun Oct 28, 2018 1:11 pm    Post subject: Re: Allis Chalmers G creeper gear failure Reply to specific post Reply with quote

Dick, I think he's referring to the lever guide pins.
 
Back to top
View user's profile
Dick L
Tractor Guru


Joined: 01 Sep 1999
Posts: 12871
Location: Edon Ohio

Report to Moderator

PostPosted: Sun Oct 28, 2018 1:49 pm    Post subject: Re: Allis Chalmers G creeper gear failure Reply to specific post Reply with quote

I'll never find out as I will never pull one down again. I just don't recall any loose pins in the five or six I had pulled all apart and put back together. I still have several transmissions in the shed.
 
Back to top
View user's profile
Mike(NEOhio)
Tractor Guru


Joined: 12 May 2013
Posts: 3853
Location: Geauga County, Ohio

Report to Moderator

PostPosted: Sun Oct 28, 2018 6:42 pm    Post subject: Re: Allis Chalmers G creeper gear failure Reply to specific post Reply with quote

Been a while since I had mine apart so I'm going by my not so great memory. Actually a pin with a squared head on it. Had to do it when the wife tried driving it and somehow got it in two gears. Never figured out how she did it but I haven't had it happen since.
 
Back to top
View user's profile
Hubschy
New User


Joined: 04 Nov 2018
Posts: 6


Report to Moderator

PostPosted: Sun Nov 04, 2018 2:28 pm    Post subject: Re: Allis Chalmers G creeper gear failure Reply to specific post Reply with quote

Are you using a "g" transmission, or a "b" transmission? The b a/c transmissions are not bored for the keepers that are required to keep the shift lever on a "g" from wobbling and jumping out of the shifter slot. I do not see the keepers, or keys, I your picture. They are a must have for the G tractor.
 
Back to top
View user's profile
neilpoulson
New User


Joined: 27 Oct 2018
Posts: 2


Report to Moderator

PostPosted: Mon Nov 05, 2018 7:18 am    Post subject: Re: Allis Chalmers G creeper gear failure Reply to specific post Reply with quote

It is a g transmission with guide pins installed. I'm not sure what picture you refer to as I didn't post any. A g transmission would also need to be drilled for the creeper shifter rod.
 
Back to top
View user's profile
Hubschy
New User


Joined: 04 Nov 2018
Posts: 6


Report to Moderator

PostPosted: Mon Nov 05, 2018 8:33 am    Post subject: Re: Allis Chalmers G creeper gear failure Reply to specific post Reply with quote

Ah, someone else posted the picture above. You are right about boring the shift lever hole and the keeper holes too on a B transmission. I'll agree with JoeM's assessment in that case.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters