Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Multipower


 
Post new topic    
View previous topic :: View next topic  
Author Message
Auctioneerajb
New User


Joined: 13 Nov 2018
Posts: 2


Report to Moderator

PostPosted: Tue Nov 13, 2018 8:35 pm    Post subject: Multipower Reply to specific post Reply with quote

Haven't used my multi power on my 275 for several years due to a linkage issue under the cover and a lack of a decent place to work on it. Well now I have a place to work on it and would like to fix it this winter. Pretty sure all it is is the rod that goes thru the cover came unhooked from the actuator on the trans. Assuming that's all it is and I get it fixed, will I have any trouble with multi power from not using it?
 
Back to top
View user's profile
Dieseltech
Tractor Guru


Joined: 29 Feb 2012
Posts: 6467
Location: Indiana

Report to Moderator

PostPosted: Wed Nov 14, 2018 5:10 am    Post subject: Re: Multipower Reply to specific post Reply with quote

Nope. It will either work, or not. The small rod should have a detent feel to it, down is Hi, up is Lo.
 
Back to top
View user's profile
Auctioneerajb
New User


Joined: 13 Nov 2018
Posts: 2


Report to Moderator

PostPosted: Wed Nov 14, 2018 6:50 am    Post subject: Re: Multipower Reply to specific post Reply with quote

Sounds promising then as it worked fine before the rod came unhooked. Reason I suspect the rod is earlier that year I had some trans work done on that required removing the cover. Judging by what I see in the service manual I think they forgot to put a cotter pin back in...
BTW how hard is it to remove that cover?
 
Back to top
View user's profile
jamstra
Regular


Joined: 11 Jun 2017
Posts: 200


Report to Moderator

PostPosted: Wed Nov 14, 2018 2:56 pm    Post subject: Re: Multipower Reply to specific post Reply with quote

Every time my MF 550 had sat unused for a couple of months or more, the multipower was always reluctant to start working again - but would
come back to life (and then stay working) after a couple of hours of field work. So when you get the linkage fixed, don't despair if it
doesn't work straight off. That's my experience anyway! Jim
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Massey Harris & Massey Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters