Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Engine mount stripped


 
Post new topic    
View previous topic :: View next topic  
Author Message
JohnMatic
New User


Joined: 04 Mar 2018
Posts: 12


Report to Moderator

PostPosted: Fri Nov 16, 2018 7:36 pm    Post subject: Engine mount stripped Reply to specific post Reply with quote

One step forward... Well I have finally finished my engine rebuild but I've hit a snag. One of the engine mounts has stripped. So my question is how important is this? Can I fill with JB Weld or do I need to remove engine and put in some type of helicoil?

Photo attached. Thanks, John

 
Back to top
View user's profile
Steve@Advance
Tractor Guru


Joined: 12 Nov 2013
Posts: 11904


Report to Moderator

PostPosted: Fri Nov 16, 2018 9:06 pm    Post subject: Re: Engine mount stripped Reply to specific post Reply with quote

Any chance there are some threads left deeper in the hole?

If so, you can bottom out a stud with some Locktite, put a nut on the stud.

But as many blots as that has, one stripped won't make any difference.
 
Back to top
View user's profile
Mike Groom
Long Time User


Joined: 07 Mar 2008
Posts: 1209


Report to Moderator

PostPosted: Sat Nov 17, 2018 7:04 am    Post subject: Re: Engine mount stripped Reply to specific post Reply with quote

If Steve's stud idea doesn't suit you it looks like the bolts are either 3/8 or 7/16,I would drill and tap it to the next size larger and call it good.I have tore
down several tractors that had just that done to them.
 
Back to top
View user's profile
MCOHIO
Regular


Joined: 06 Nov 2011
Posts: 52


Report to Moderator

PostPosted: Sat Nov 17, 2018 7:08 am    Post subject: Re: Engine mount stripped Reply to specific post Reply with quote

I had a 48 TE that had the same problem with 4 being stripped. I used thread repair inserts- not Heli-coil. I used the tractor for several years after that with no issues. A Heli-coil may very well be strong enough as well but I would not trust any epoxy to repair the threads.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Harry Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters