Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

D19 engine serial number


 
Post new topic    
View previous topic :: View next topic  
Author Message
Napper2.0
New User


Joined: 27 Dec 2018
Posts: 1


Report to Moderator

PostPosted: Thu Dec 27, 2018 10:27 am    Post subject: D19 engine serial number Reply to specific post Reply with quote

I just bought a D19 gasser. Serial number on tractor is 12968. The engine runs, but the owner before me said it had a blown head gasket or cracked head. I am fairly certain it is a G262, but I cant find the engine serial number. I have found several numbers cast into the block such as 3563 and D45128 then 80 stamped behind. Is the number that starts with D the engine serial number? Seems one digit too long to me. I want to order the right gasket assembley. I also have a similar G262 engine out of a Gleaner combine. It has a Zenith 12777 carb on it. Does anyone know if that carb can be switched out with the original TSX 848 carb? Would the heads be the same also?
 
Back to top
View user's profile
Mr.Ferguson
Regular


Joined: 15 Aug 2018
Posts: 43


Report to Moderator

PostPosted: Thu Dec 27, 2018 5:04 pm    Post subject: Re: D19 engine serial number Reply to specific post Reply with quote

First, lord help your wallet, those things can chow down 60 gallons of fuel a day! But that dose have a G262 for a motor. Good motor.
 
Back to top
View user's profile
fastfarmall
Tractor Expert


Joined: 05 Feb 2015
Posts: 3443


Report to Moderator

PostPosted: Sun Dec 30, 2018 12:33 pm    Post subject: Re: D19 engine serial number Reply to specific post Reply with quote

That's no worse than a 706 IHC, and about the same size engine,you want it to burn that much fuel,the leaner the mixture the hotter the flame.if it run's to lean it will cause more valve and head troubles !!
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters