Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

125E


 
Post new topic    
View previous topic :: View next topic  
Author Message
TnJoe
New User


Joined: 14 Sep 2007
Posts: 9


Report to Moderator

PostPosted: Sun Dec 30, 2018 11:41 am    Post subject: 125E Reply to specific post Reply with quote

Could someone tell how to remove the master switch from my dresser 125e ? It has 2 bolts that unbolt it from sheet metal but the hole it goes through is to small for the switch to come out. Is there a way to disassemble the switch so it can come out in 2 pieces.
 
Back to top
View user's profile
jm.
Tractor Guru


Joined: 11 Apr 2010
Posts: 5488
Location: Dover Tenn.

Report to Moderator

PostPosted: Mon Dec 31, 2018 2:49 pm    Post subject: Re: 125E Reply to specific post Reply with quote

Joe it goes in, you remove the wires and then it will push in and remove from the back side
 
Back to top
View user's profile
TnJoe
New User


Joined: 14 Sep 2007
Posts: 9


Report to Moderator

PostPosted: Mon Dec 31, 2018 3:08 pm    Post subject: Re: 125E Reply to specific post Reply with quote

CVPost-jm. wrote:
(quoted from post at 23:49:30 12/31/1Cool Joe it goes in, you remove the wires and then it will push in and remove from the back side

I tried to push it in but the handle is a T handle and its to big to go through the hole. I tried to twist it around so maybe I could get one side of the handle in the hole but nothing worked.
 
Back to top
View user's profile
jm.
Tractor Guru


Joined: 11 Apr 2010
Posts: 5488
Location: Dover Tenn.

Report to Moderator

PostPosted: Mon Dec 31, 2018 5:41 pm    Post subject: Re: 125E Reply to specific post Reply with quote

Look hard should be a little bitty Philips screw in the center of that T, it can be removed then the handle comes off. Where in Tenn are you located?
 
Back to top
View user's profile
TnJoe
New User


Joined: 14 Sep 2007
Posts: 9


Report to Moderator

PostPosted: Mon Dec 31, 2018 7:42 pm    Post subject: Re: 125E Reply to specific post Reply with quote

Jim
I'm from Kingston, that's exit 352 off I40.

I thought the handle should come off, I looks at it and it looks like it is braded on. Its a strange switch, center position is on and about 45 degree off center either way is off and lockable. I will take a file and hit the end of the T and that should show me if its solid or not.
 
Back to top
View user's profile
jm.
Tractor Guru


Joined: 11 Apr 2010
Posts: 5488
Location: Dover Tenn.

Report to Moderator

PostPosted: Tue Jan 01, 2019 5:14 am    Post subject: Re: 125E Reply to specific post Reply with quote

My e mail is open let me know what you find. That is how the switch works. Was wondering why you want to remove it. It should be set up to break the ground cable . I am about 45 minutes west of you. Years of ih experience
 
Back to top
View user's profile
DWF
Regular


Joined: 05 Mar 2009
Posts: 384
Location: NW Wisconsin

Report to Moderator

PostPosted: Wed Jan 02, 2019 1:49 pm    Post subject: Re: 125E Reply to specific post Reply with quote

I took one of those off my TD15-C and put a keyed master switch on instead. I saved that old switch and just looked at it and there is two small bolts (probably 1'4") that hold that switch on. There is a small screw that needs an allen wrench that holds that T on, but on mine all that needs done is the two bolts removed. I had a TD8-E that had that type of switch, but I no longer have that to look at.
DWF
 
Back to top
View user's profile
TnJoe
New User


Joined: 14 Sep 2007
Posts: 9


Report to Moderator

PostPosted: Wed Jan 02, 2019 3:12 pm    Post subject: Re: 125E Reply to specific post Reply with quote

Jim, I cant get the switch to make contact, I can short across the posts on the back and it starts fine just wont charge the battery.

Where is the screw located, in the barrel or the T handle. I removed the two bolts and the wires on the back, turned it every way I could looking for other bolts or set screws. The weather here has been bad for the last few days (raining) when clears up I will look at it again, maybe take some photos of it.

I sure want to thank you all for responding to my post. I wont give up. If I have to I will cut a slot in the sheet metal so the T handle will go through the back Smile
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Crawlers, Dozers, Loaders and Backhoes All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters