Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

original tool for bolt stops CA spin outs


 
Post new topic    
View previous topic :: View next topic  
Author Message
jerkus730
Regular


Joined: 21 Oct 2015
Posts: 39


Report to Moderator

PostPosted: Tue Jan 01, 2019 7:01 pm    Post subject: original tool for bolt stops CA spin outs Reply to specific post Reply with quote

Does anybody have one or know where I can buy one?
 
Back to top
View user's profile
switch
Regular


Joined: 25 Jan 2017
Posts: 39


Report to Moderator

PostPosted: Tue Jan 01, 2019 8:29 pm    Post subject: Re: original tool for bolt stops CA spin outs Reply to specific post Reply with quote

I am not following what tool you're looking for. Did you have a picture or part number? I have a bunch of the old original tools
 
Back to top
View user's profile
Fred2
Regular


Joined: 30 Jan 2012
Posts: 88


Report to Moderator

PostPosted: Wed Jan 02, 2019 10:33 am    Post subject: Re: original tool for bolt stops CA spin outs Reply to specific post Reply with quote

He is probably talking about the wheel wrench that Allis had for new tractors it had a socket on both ends with a hole in each end for a bar. I have one but don't want to sell it
 
Back to top
View user's profile
Jim.ME
Regular


Joined: 02 Mar 2018
Posts: 484
Location: western Maine

Report to Moderator

PostPosted: Wed Jan 02, 2019 2:18 pm    Post subject: Re: original tool for bolt stops CA spin outs Reply to specific post Reply with quote

Are you looking for an original wrench just to have one? According to the AGCO parts books on line the part number for the CA rear wrench is 70225339 and the handle for it is 70225340. I don’t know the actual sizes of that wrench, it may just fit the hex nuts holding the eccentric blocks, or wheel centers to the axle, and the front wheel hex bolts.

Are you looking for a wrench that will work on the wheel stop capscrews and eccentric pins, or on the nuts of the bolts that hold the eccentric blocks on the wheel centers? I use a 1/2” 8-point socket on the wheel stop capscrews and eccentrics. Sometimes it takes a bit on filing on the eccentric pin heads if they have been banged up. The 5/8” nuts that hold the eccentric blocks on are 1” hex on my CA.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters