Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Oliver 60rc help


 
Post new topic    
View previous topic :: View next topic  
Author Message
Brianjbell
Regular


Joined: 07 Jan 2012
Posts: 143


Report to Moderator

PostPosted: Fri Jan 04, 2019 6:37 pm    Post subject: Oliver 60rc help Reply to specific post Reply with quote

All, I'm new to Oliver. I have the opportunity to pickup a 60rc right not far down the road. Has part of a set of cultivator. Supposed to run, but haven't seen it yet. What should I be looking for and how hard are parts to come by for it? I'm used to the relative ease finding parts for a Ford. Thanks in advance.
 
Back to top
View user's profile
Olliejunkie
Tractor Expert


Joined: 22 May 2016
Posts: 2468
Location: Eugene Oregon

Report to Moderator

PostPosted: Fri Jan 04, 2019 6:54 pm    Post subject: Re: Oliver 60rc help Reply to specific post Reply with quote

Check the frame for cracks. They're pressed steel and cultivators are kinda hard on them. If it's a wide front look for welds and cracks. If it has 7 lug wheels they can be hard to find. Cracks in block. Particularly the left side.
 
Back to top
View user's profile
JOCCO
Tractor Expert


Joined: 14 Feb 2003
Posts: 3394


Report to Moderator

PostPosted: Sun Jan 06, 2019 7:41 am    Post subject: Re: Oliver 60rc help Reply to specific post Reply with quote

From what I see a 60 should not be to hard to get parts for. Barring aside unusual items. They may not be as cheap as Ford.
 
Back to top
View user's profile
Brian Jasper co. Ia
Tractor Expert


Joined: 16 Dec 2007
Posts: 2962


Report to Moderator

PostPosted: Sun Jan 06, 2019 3:31 pm    Post subject: Re: Oliver 60rc help Reply to specific post Reply with quote

There's a fair amount of stuff that is 60 only. Parts can be had if you know where to look. I completely rebuilt a 60 and the only place I was able to find engine parts like main bearings and sleeves/pistons was at Maibach Tractor in Creston OH. As far as I can tell they are the 60 tractor specialists. They treated me very well and I wouldn't hesitate to buy from them again.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters