Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Case M series brush harrow


 
Post new topic    
View previous topic :: View next topic  
Author Message
Ellis Kinney
Tractor Expert


Joined: 09 Apr 2011
Posts: 1627


Report to Moderator

PostPosted: Fri Jan 11, 2019 1:59 pm    Post subject: Case M series brush harrow Reply to specific post Reply with quote

Please refer to my previous same post on page 2. I found the foundry in South Dakota that will make the bushings VR-2702. Approximately $75.00 per bushing and I need 8 of them. That is $600.00 plus shipping which would be a lot. I gave $300.00 for the bog harrow and another $300.00 for the disc cutters plus all new bolts and nuts when I rebuilt it. I had a couple of busted bushings which I welded up with nickel rod. You can see where I am going with this, pretty soon I'll have a million in it. I know that somewhere out there is an old warehouse with a bunch of these bushings stuck up on a shelf in the back. Just an update and thank you for those who tried to help. Ellis
 
Back to top
View user's profile
SVcummins
Tractor Guru


Joined: 06 Feb 2017
Posts: 6548


Report to Moderator

PostPosted: Sat Jan 12, 2019 12:53 am    Post subject: Re: Case M series brush harrow Reply to specific post Reply with quote

I look at it like this . These old implements are built a lot better than the new stuff of this size 900$ might buy you a tin foil and bubblegum built disk that?s made to light and you still won?t have anything
 
Back to top
View user's profile
showcrop
Tractor Guru


Joined: 13 Dec 2000
Posts: 22004
Location: Chester NH

Report to Moderator

PostPosted: Sat Jan 12, 2019 3:37 am    Post subject: Re: Case M series brush harrow Reply to specific post Reply with quote


What happened to getting a machine shop to make them for you? It would probably cost 1/3 as much.
 
Back to top
View user's profile
ghostdncr
Regular


Joined: 02 Dec 2018
Posts: 101


Report to Moderator

PostPosted: Sat Jan 12, 2019 3:56 am    Post subject: Re: Case M series brush harrow Reply to specific post Reply with quote

Hey Ellis, Part #'s 2702 and 810-X look like two half-bushings that mate together to make one, with 810-X possibly having a Zerk fitting. Is this correct? I'm a working machinist and don't think that would be much of a job at all. Thing is if you need zero gap where they mate together, you'll have to turn sixteen of them in the round and then throw almost half of each one in the scrap bin. If a gap the width of a saw blade, say 1/32" or so wouldn't hurt, then you could get by just turning eight. Do you have a vocational or trade school within a reasonable distance from you? I'll bet they could help out on the cheap if they have any kind of machine shop training program.
 
Back to top
View user's profile
Ellis Kinney
Tractor Expert


Joined: 09 Apr 2011
Posts: 1627


Report to Moderator

PostPosted: Sat Jan 12, 2019 8:27 am    Post subject: Re: Case M series brush harrow Reply to specific post Reply with quote

You are correct about the two halves being the same except for a grease fitting. They do touch where they mate together....But....I could build them up
slightly with nickel and file them down to fit. The bearing is kind of a loose fit inside the bushings. Ellis
 
Back to top
View user's profile
Ellis Kinney
Tractor Expert


Joined: 09 Apr 2011
Posts: 1627


Report to Moderator

PostPosted: Sat Jan 12, 2019 8:31 am    Post subject: Re: Case M series brush harrow Reply to specific post Reply with quote

It doesn't look like it in the picture, but this thing weighs about 1400 lbs. according to my owners manual. I can buy one from TSC for $400.00 but not nearly the same piece of equipment! Ellis
 
Back to top
View user's profile
Ellis Kinney
Tractor Expert


Joined: 09 Apr 2011
Posts: 1627


Report to Moderator

PostPosted: Sat Jan 12, 2019 8:33 am    Post subject: Re: Case M series brush harrow Reply to specific post Reply with quote

I am going to take it apart so I will have an example for a machinist and see what I can find. Ellis
 
Back to top
View user's profile
Leroy
Tractor Guru


Joined: 09 Jan 1998
Posts: 18208
Location: Wapakoneta, Ohio

Report to Moderator

PostPosted: Sat Jan 12, 2019 1:05 pm    Post subject: Re: Case M series brush harrow Reply to specific post Reply with quote

Unless that saw cut would be enough to make a difference in the mounting of the bearing housing that saw cut would just make it fit that much better on a worn rest of part bearing.
 
Back to top
View user's profile
SVcummins
Tractor Guru


Joined: 06 Feb 2017
Posts: 6548


Report to Moderator

PostPosted: Sat Jan 12, 2019 10:13 pm    Post subject: Re: Case M series brush harrow Reply to specific post Reply with quote

It would take 3 tsc disks to make one of the disks you have and then you still wouldn?t have anything
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Implement Alley All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters