Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

TO 30 Spun ROD bearings


 
Post new topic    
View previous topic :: View next topic  
Author Message
DavidBond
New User


Joined: 16 Jul 2012
Posts: 17
Location: WASHINGTON STATE

Report to Moderator

PostPosted: Fri Jan 18, 2019 12:58 am    Post subject: TO 30 Spun ROD bearings Reply to specific post Reply with quote

Neighbor brought over his To 30 because motor was making knocking noise. I pulled the pan and was surprised to see rods 3 & 4 dry, no oil on them at all and bearing spun on 4. Rods 1 &2 were wet. What would cause this to happen. plenty of good oil in motor. Looking at as much of the motor that I could see, there was plenty of oil being pumped though the motor.

Since the labor charges will be more than tractor is worth owner will probably sell it to me. I do not know so much about Fergusons used part market since I have an 8N. Is there much market for TO parts. Tractor does have a Sherman combo in it and lot of other good parts. Plus it has a jungle gym bucket on it also.
 
Back to top
View user's profile
Bruce(OR)
Tractor Expert


Joined: 10 Apr 2007
Posts: 2622


Report to Moderator

PostPosted: Fri Jan 18, 2019 6:17 am    Post subject: Re: TO 30 Spun ROD bearings Reply to specific post Reply with quote

Parting it should bring a fair amount. Ford can use the Ferguson Sherman combo. Ferguson cannot directly use the Ford Sherman combo. The top
lid is a different design. The engine block itself might get you a buck or two.
The engine might interest me more than it should. You didn't say where you are located.
Fergy parts sell better in another month or two.
 
Back to top
View user's profile
John Deere D
Tractor Expert


Joined: 14 Jun 2011
Posts: 3310


Report to Moderator

PostPosted: Fri Jan 18, 2019 7:01 am    Post subject: Re: TO 30 Spun ROD bearings Reply to specific post Reply with quote

Quote:
Neighbor brought over his To 30 because motor was making knocking noise. I pulled the pan and was surprised to see rods 3 & 4 dry, no oil on them at all and
bearing spun on 4. Rods 1 &2 were wet. What would cause this to happen. plenty of good oil in motor. Looking at as much of the motor that I could see, there was plenty of oil being pumped though the motor.

Tractor does have a Sherman combo in it.....

Good morning DavidBond:

If you or your neighbor should decide to part out this TO 30, I'm interested in the Sherman Combo. I own and operate a Ferguson TEA 20 that requires a Sherman Combo.

My understanding of the Sherman Combo, is the Combo has both overdrive and under drive capabilities?

If so, I'm interested in this Sherman Combo for my daily user.

Thanks

Bob....
 
Back to top
View user's profile
beige35
Regular


Joined: 10 Nov 2015
Posts: 67


Report to Moderator

PostPosted: Fri Jan 18, 2019 6:19 pm    Post subject: Re: TO 30 Spun ROD bearings Reply to specific post Reply with quote

[quote="DavidBond"](quoted from post at 01:58:38 01/18/19) Neighbor brought over his To 30 because motor was making knocking noise. I pulled the pan and was surprised to see rods 3 & 4 dry, no oil on them at all and bearing spun on 4. Rods 1 &2 were wet. What would cause this to happen. plenty of good oil in motor. Looking at as much of the motor that I could see, the re was plenty of oil being pumped though the motor. I would look at the oil pump Sounds like a oil pressure problem
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Harry Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters