Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

310t crankshaft grind


 
Post new topic    
View previous topic :: View next topic  
Author Message
$$4toys
Regular


Joined: 11 Dec 2018
Posts: 35


Report to Moderator

PostPosted: Sat Jan 19, 2019 5:36 am    Post subject: 310t crankshaft grind Reply to specific post Reply with quote

Has anyone on here with 310t experience ever heard of grinding a 310 crank to 0.030? After a lot of hours searching this site I ran across one older post for an engine with a crank ground to 0.030.
 
Back to top
View user's profile
Dieseltech
Tractor Guru


Joined: 29 Feb 2012
Posts: 6844
Location: Indiana

Report to Moderator

PostPosted: Sat Jan 19, 2019 6:09 am    Post subject: Re: 310t crankshaft grind Reply to specific post Reply with quote

Not sure about .030, but I have a 283 apart now with .010 under rod bearings..
 
Back to top
View user's profile
$$4toys
Regular


Joined: 11 Dec 2018
Posts: 35


Report to Moderator

PostPosted: Sat Jan 19, 2019 6:51 am    Post subject: Re: 310t crankshaft grind Reply to specific post Reply with quote

CVPost-Dieseltech wrote:
(quoted from post at 07:09:38 01/19/19) Not sure about .030, but I have a 283 apart now with .010 under rod bearings..


Was going to change out the rod bolts and wrist pins, very disappointed once I pulled the caps. 1 & 2 mains and 1 & 2 rods, rod bearings show bearing failure, starting flake and 3-6 look good. Not sure why, but it has to be an oil supply issue. Crank already at .020 main/.010 rods. if it was only one (1) journal I would have it welded/built up, but two (2) they say can't be done.
 
Back to top
View user's profile
J. Schwiebert
Tractor Guru


Joined: 27 Sep 2013
Posts: 4204


Report to Moderator

PostPosted: Sat Jan 19, 2019 1:37 pm    Post subject: Re: 310t crankshaft grind Reply to specific post Reply with quote

Make sure you check the clearance on the oil pump. Also have the line bore of the engine checked as well. Do you know what the bearing clearance was when you took the engine apart? You can send me an e-mail and include your phone number. J.
 
Back to top
View user's profile
$$4toys
Regular


Joined: 11 Dec 2018
Posts: 35


Report to Moderator

PostPosted: Sat Jan 19, 2019 2:50 pm    Post subject: Re: 310t crankshaft grind Reply to specific post Reply with quote

CVPost-J. Schwiebert wrote:
(quoted from post at 14:37:38 01/19/19) Make sure you check the clearance on the oil pump. Also have the line bore of the engine checked as well. Do you know what the bearing clearance was when you took the engine apart? You can send me an e-mail and include your phone number. J.


I did not check the clearance. Once I saw the crank, I knew knew I was in trouble here, too rough to reuse and already at .020. I don't have an email address for you, but you can send one to me at 74ollie1955@gmail.com
 
Back to top
View user's profile
J. Schwiebert
Tractor Guru


Joined: 27 Sep 2013
Posts: 4204


Report to Moderator

PostPosted: Sat Jan 19, 2019 4:47 pm    Post subject: Re: 310t crankshaft grind Reply to specific post Reply with quote

Your e-mail came back to me. My e-mail should be open in modern view. J.
 
Back to top
View user's profile
johns
Long Time User


Joined: 09 Oct 2008
Posts: 948


Report to Moderator

PostPosted: Sat Jan 19, 2019 5:10 pm    Post subject: Re: 310t crankshaft grind Reply to specific post Reply with quote

Larry Harsin has a 310 crank for sale Rods at 030, mains at 020. I would call and ask him what he thinks about your crankshaft.
712-362-2966

www.olivertractor.com
 
Back to top
View user's profile
$$4toys
Regular


Joined: 11 Dec 2018
Posts: 35


Report to Moderator

PostPosted: Sat Jan 19, 2019 6:13 pm    Post subject: Re: 310t crankshaft grind Reply to specific post Reply with quote

CVPost-J. Schwiebert wrote:
(quoted from post at 17:47:36 01/19/19) Your e-mail came back to me. My e-mail should be open in modern view. J.


I am not sure why it didn't come through, I just an email from my other account to this one and it worked. In your profile I can't access your email either. Care to try the 74ollie1955@gmail.com once again?
 
Back to top
View user's profile
$$4toys
Regular


Joined: 11 Dec 2018
Posts: 35


Report to Moderator

PostPosted: Sat Jan 19, 2019 6:24 pm    Post subject: Re: 310t crankshaft grind Reply to specific post Reply with quote


I will probably talk to Larry about this, but at least it's good to know that if he has one ground to .030, so there must be some bearings out there. Thanks for the info. A .030 grind does not exactly give a person that warm and fuzzy feeling though, does it?
I guess I was curious if there was someone who was actually running one with .030 grind. I have two options on another complete engine, oil cooled, high serial number, don't think this one has been apart yet, but it's by no means a guarantee to be better than what I have, and its not exactly a give away either.
the other is a crank I just heard about.
 
Back to top
View user's profile
J. Schwiebert
Tractor Guru


Joined: 27 Sep 2013
Posts: 4204


Report to Moderator

PostPosted: Sun Jan 20, 2019 6:00 am    Post subject: Re: 310t crankshaft grind Reply to specific post Reply with quote

In modern view my e-mail is open. I will try later.
 
Back to top
View user's profile
J. Schwiebert
Tractor Guru


Joined: 27 Sep 2013
Posts: 4204


Report to Moderator

PostPosted: Sun Jan 20, 2019 11:14 am    Post subject: Re: 310t crankshaft grind Reply to specific post Reply with quote

The second time also failed. Look in modern view for mine. J.
 
Back to top
View user's profile
scootergmc
Regular


Joined: 30 Mar 2015
Posts: 171
Location: Sunny California

Report to Moderator

PostPosted: Sun Jan 20, 2019 11:58 am    Post subject: Re: 310t crankshaft grind Reply to specific post Reply with quote

CVPost-J. Schwiebert wrote:
(quoted from post at 12:14:50 01/20/19) The second time also failed. Look in modern view for mine. J.


J- I'm in modern view and your email isn't showing anymore.
 
Back to top
View user's profile
$$4toys
Regular


Joined: 11 Dec 2018
Posts: 35


Report to Moderator

PostPosted: Sun Jan 20, 2019 12:05 pm    Post subject: Re: 310t crankshaft grind Reply to specific post Reply with quote


Thanks for the post, I thought I was loosing it !
 
Back to top
View user's profile
$$4toys
Regular


Joined: 11 Dec 2018
Posts: 35


Report to Moderator

PostPosted: Sun Jan 20, 2019 7:30 pm    Post subject: Re: 310t crankshaft grind Reply to specific post Reply with quote


J., your email is not available to me. I do not see it in any of your posts.
 
Back to top
View user's profile
Young Mechanic
Regular


Joined: 08 May 2017
Posts: 91


Report to Moderator

PostPosted: Mon Jan 21, 2019 6:12 pm    Post subject: Re: 310t crankshaft grind Reply to specific post Reply with quote

We have a 310 gas we ground to .040 on the rods, couple years ago. Holding fine for now. Course we just move bales and stuff with it, burns to much
gas for heavy work.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters