Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Ford 134 cid


 
Post new topic    
View previous topic :: View next topic  
Author Message
Farmallgreen
New User


Joined: 27 Aug 2018
Posts: 7


Report to Moderator

PostPosted: Sat Feb 09, 2019 8:14 pm    Post subject: Ford 134 cid Reply to specific post Reply with quote

Anybody no what the compression height is on a ford 134 piston, can?t find any info on this. They have same bore as 262 allis trying to find higher comp piston to put in the 262. Thanks for any help.
 
Back to top
View user's profile
Gary H.
Regular


Joined: 11 Jul 2007
Posts: 290


Report to Moderator

PostPosted: Sun Feb 10, 2019 6:12 am    Post subject: Re: Ford 134 cid Reply to specific post Reply with quote

Check with Mike Lepard snappytractor66@yahoo.com
 
Back to top
View user's profile
VicS
Tractor Guru


Joined: 12 Mar 2010
Posts: 4744


Report to Moderator

PostPosted: Sun Feb 10, 2019 5:34 pm    Post subject: Re: Ford 134 cid Reply to specific post Reply with quote

I've got some diesel pistons. But they are still in the engine. Located in SE Illinois. You would have to come get them.
 
Back to top
View user's profile
red30
Regular


Joined: 08 Jan 2013
Posts: 26


Report to Moderator

PostPosted: Mon Feb 11, 2019 5:08 pm    Post subject: Re: Ford 134 cid Reply to specific post Reply with quote

hi

I looked that 134 ford up its only 3.437 bore not 3.562 and there too tall for any reasonable compression ratio but if you get in touch with me I can help you out

Mike LePard
 
Back to top
View user's profile
Farmallgreen
New User


Joined: 27 Aug 2018
Posts: 7


Report to Moderator

PostPosted: Tue Feb 12, 2019 9:35 am    Post subject: Re: Ford 134 cid Reply to specific post Reply with quote

I would like to talk to you if you can call me 318 557 4283
 
Back to top
View user's profile
ejr-IA.
Long Time User


Joined: 19 Oct 2009
Posts: 756


Report to Moderator

PostPosted: Wed Feb 13, 2019 3:40 pm    Post subject: Re: Ford 134 cid Reply to specific post Reply with quote

Compression ht is from center of wrist pin to top is 2.090
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Pulling All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters