Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

minnie power plant.


 
Post new topic    
View previous topic :: View next topic  
Author Message
rustred
Tractor Guru


Joined: 01 Jul 2009
Posts: 30910


Report to Moderator

PostPosted: Wed Feb 27, 2019 6:13 pm    Post subject: minnie power plant. Reply to specific post Reply with quote

got this engine, was wondering what tractor it would be from.it says model 336 4A on the tag.





 
Back to top
View user's profile
shaun wallace
Tractor Expert


Joined: 11 May 2008
Posts: 3235


Report to Moderator

PostPosted: Wed Feb 27, 2019 6:58 pm    Post subject: Re: minnie power plant. Reply to specific post Reply with quote

M5 and M series.
 
Back to top
View user's profile
ChrisQ
Regular


Joined: 05 Nov 2012
Posts: 294
Location: Jordan, MN

Report to Moderator

PostPosted: Wed Feb 27, 2019 8:09 pm    Post subject: Re: minnie power plant. Reply to specific post Reply with quote

Older series 336 crankcase. Would be correct for 5 Star, M5, M602, and M670 non super. Heads and bore size would make it correct for M5 or M602.
 
Back to top
View user's profile
molinegb
Tractor Expert


Joined: 13 Feb 2005
Posts: 2480


Report to Moderator

PostPosted: Fri Mar 01, 2019 8:00 am    Post subject: Re: minnie power plant. Reply to specific post Reply with quote

Not a 5 Star crankcase. They used 283 gas. 336 was diesel.
 
Back to top
View user's profile
rustred
Tractor Guru


Joined: 01 Jul 2009
Posts: 30910


Report to Moderator

PostPosted: Fri Mar 01, 2019 7:32 pm    Post subject: Re: minnie power plant. Reply to specific post Reply with quote

so is this the same heads the U has and will the manifold fit a model U ?
 
Back to top
View user's profile
molinegb
Tractor Expert


Joined: 13 Feb 2005
Posts: 2480


Report to Moderator

PostPosted: Sat Mar 02, 2019 6:13 am    Post subject: Re: minnie power plant. Reply to specific post Reply with quote

All heads will interchange as well as manifold. Manifold may have to be trimmed a bit. Have a 336 lp manifold on a 1947 UTS with solid block.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Minneapolis Moline All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters