Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

NAA Alternator pics


 
Post new topic    
View previous topic :: View next topic  
Author Message
Olliejunkie
Tractor Expert


Joined: 22 May 2016
Posts: 2679
Location: Eugene Oregon

Report to Moderator

PostPosted: Thu Mar 14, 2019 3:23 pm    Post subject: NAA Alternator pics Reply to specific post Reply with quote

Friend has a NAA that someone added a alternator. I had a homemade bracket. Everything was out of line and crooked. I purchased a bracket online but now the alternator hits the exhaust. The pulley stuck out quite a ways to I brought it home and put a different pulley on it. Hope it works but the shaft still may hit. I'm wondering what some of yours look like?
 
Back to top
View user's profile
JMOR
Tractor Guru


Joined: 13 Aug 2007
Posts: 23972


Report to Moderator

PostPosted: Thu Mar 14, 2019 7:51 pm    Post subject: Re: NAA Alternator pics Reply to specific post Reply with quote

If the belt lines up, then the exhaust is the problem. If belt does not line up, then the alt bracket is the problem.
 
Back to top
View user's profile
Sean in PA
Tractor Guru


Joined: 27 Feb 2008
Posts: 7381
Location: Southeast PA

Report to Moderator

PostPosted: Fri Mar 15, 2019 4:48 am    Post subject: Re: NAA Alternator pics Reply to specific post Reply with quote

Would a shorter belt allow you to adjust the alternator further in so that it wouldn't hit the exhaust?
 
Back to top
View user's profile
Olliejunkie
Tractor Expert


Joined: 22 May 2016
Posts: 2679
Location: Eugene Oregon

Report to Moderator

PostPosted: Fri Mar 15, 2019 12:25 pm    Post subject: Re: NAA Alternator pics Reply to specific post Reply with quote

JMOR wrote:
(quoted from post at 20:51:40 03/14/19) If the belt lines up, then the exhaust is the problem. If belt does not line up, then the alt bracket is the problem.

I think they used the pulley of the generator and it sticks out to far so the bracket couldn't line up. I will try to find a picture. Will be over there later to see if new pulley helps.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Ford All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters