Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

H belt pulley removal


 
Post new topic    
View previous topic :: View next topic  
Author Message
George by Geneva, NY
Regular


Joined: 06 Mar 2015
Posts: 218


Report to Moderator

PostPosted: Sun Apr 14, 2019 8:26 pm    Post subject: H belt pulley removal Reply to specific post Reply with quote

Well, I went into the unknown, started to remove belt pulley so as to check for plugged drain of oil back in to reduction gear case. Tractor is sn under 10,000. Took snap ring off splined shaft, moved the pulley out about an inch and it stopped. I did too, as I now realize that the fork has to be loose or removed, maybe something else to free it up. Owner manual no help. Anyone out there that can give me info on what has to be done? One thing for sure I do not want to break anything, I was hoping for a quick off, clean the drain hole and put it back together.
 
Back to top
View user's profile
George by Geneva, NY
Regular


Joined: 06 Mar 2015
Posts: 218


Report to Moderator

PostPosted: Sun Apr 14, 2019 9:13 pm    Post subject: Re: H belt pulley removal Reply to specific post Reply with quote

Just got a look at the parts diagram on the computer and enlarged it. Looks like nut,#54, gets the fork shaft out and the fork out of the way. Then is anything still holding the pulley on???
 
Back to top
View user's profile
Mike(NEOhio)
Tractor Guru


Joined: 12 May 2013
Posts: 4435
Location: Geauga County, Ohio

Report to Moderator

PostPosted: Mon Apr 15, 2019 3:18 am    Post subject: Re: H belt pulley removal Reply to specific post Reply with quote

Long time since I tore mine apart but it should just slide off after you remove the drive disk and fork. What snap ring are you talking about? Take off the block that holds the clutch lever pin and remove the fork from the front after you pull up the fork shaft. Don't lose the spring and thrust washers under the shaft. The fork arms have an offset to one side. Mark it for reassembly.
 
Back to top
View user's profile
fpappal
Regular


Joined: 25 Jan 2014
Posts: 302


Report to Moderator

PostPosted: Mon Apr 15, 2019 4:10 am    Post subject: Re: H belt pulley removal Reply to specific post Reply with quote

I restored my 1941 a few years back and found a couple pics that might help you. I do not recall a snap ring,from what I remember it just slid off the splined shaft.







 
Back to top
View user's profile
D-
Tractor Expert


Joined: 17 Jun 2013
Posts: 2509


Report to Moderator

PostPosted: Mon Apr 15, 2019 6:22 am    Post subject: Re: H belt pulley removal Reply to specific post Reply with quote

You have to remove all the clutch.
The hub is on tapered splines and has to be pulled.
 
Back to top
View user's profile
dan_41jdh
Long Time User


Joined: 23 Mar 2001
Posts: 637


Report to Moderator

PostPosted: Mon Apr 15, 2019 7:57 am    Post subject: Re: H belt pulley removal Reply to specific post Reply with quote

George, you're on the right track. Your early "H" doesn't have items 2, 3 & 4, but does have items 10, 11, and 12. You apparently pried out that ornery snap ring #11. And your early "H" camshaft and clutch disc have straight splines and the snap ring holds the clutch onto the camshaft, whereas the later (more robust) tractors had tapered splines in that area, thus requiring a puller to remove the clutch disc. You've got the hard part done, but the #60 fork is still holding the pulley in place. So in sequence, from the rest of the diagram not shown, remove nut 52, then lever 53 (warning- tapered splines between lever 53 and shaft 56), then bearing nut 54, then you can pull out shaft 56 and misc parts (spring, etc.) and finally, fork 60 is free. As Mike mentioned, mark the relationship between 53, 56, and 60 because it'll make reassembly a lot easier than having to do trial and error checks during reassembly.

 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> John Deere All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters