Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

dynahoe 190


 
Post new topic    
View previous topic :: View next topic  
Author Message
sticky1
New User


Joined: 21 Aug 2017
Posts: 2


Report to Moderator

PostPosted: Mon Aug 21, 2017 4:32 am    Post subject: dynahoe 190 Reply to specific post Reply with quote

serial number 2000....E

Does anyone know the master cyl part number?

does the brake cyl take hyd fluid or dot 3 break fluid?

The diagram looks like the master cyl is tied to the hyd res.
 
Back to top
View user's profile
AJ.
Tractor Expert


Joined: 20 Oct 2007
Posts: 2007
Location: UK

Report to Moderator

PostPosted: Mon Aug 21, 2017 2:49 pm    Post subject: Re: dynahoe 190 Reply to specific post Reply with quote

Not 100% sure but I think the master cylinder was made by Wagner,see if there is a part number stamped on it,if not measure the bore and contact them for a dealer near you,they may be able to supply a repair kit that would get you out of trouble,I don't know about the fluid but a lot of machines do have the brakes hooked to the hydraulics,if it has remember the engine has to be on low idle when bleeding.
AJ
http://www.wagnerbrake.com/products/brakes/wagner-hydraulics-hardware.html
 
Back to top
View user's profile
Seeman
New User


Joined: 17 Apr 2019
Posts: 1


Report to Moderator

PostPosted: Wed Apr 17, 2019 2:14 am    Post subject: Re: dynahoe 190 Reply to specific post Reply with quote

do you know if there is a way to toe a 190 without hurting the hydrostatic pumps ?? Like disengage something???
 
Back to top
View user's profile
harleyg3
New User


Joined: 31 Jul 2019
Posts: 1


Report to Moderator

PostPosted: Wed Jul 31, 2019 7:29 am    Post subject: Re: dynahoe 190 Reply to specific post Reply with quote

If you have the dual master cylinder w/ air actuators, the Dorman part number is DOR M661 which is available and fairly inexpensive. I bought a pair from a local distributor for less than $70 each
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Crawlers, Dozers, Loaders and Backhoes All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters