Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

1010 Gas Rebuild

Goto page Previous  1, 2

Post new topic    
View previous topic :: View next topic  
Author Message
Glen D Anderson
Long Time User

Joined: 21 Aug 2008
Posts: 1005

Report to Moderator

PostPosted: Fri Sep 21, 2018 11:02 am    Post subject: Re: 1010 Gas Rebuild Reply to specific post Reply with quote

I see now, makes sense......LOL

Mnethercutt wrote:
(quoted from post at 08:44:35 09/21/18) Oh no, I didn't mean buy the combine motor for the crank. I would buy a running combine then take the engine from that and bolt it into my tractor. I get more horsepower with the 145 and better parts availability. I wouldn't go the combine route unless I could see it running in person.

Back to top
View user's profile
New User

Joined: 14 May 2019
Posts: 1

Report to Moderator

PostPosted: Wed May 15, 2019 8:59 am    Post subject: Re: 1010 Gas Rebuild Reply to specific post Reply with quote

Hay maker2 wrote:
(quoted from post at 12:16:27 09/19/18)
Mnethercutt wrote:
(quoted from post at 19:02:44 09/19/18)
Bumping this back up 2 ask 2 questions.

1. are the specs I posted above too out to get turned or can I get by with just new bearings or something in the middle?

2. Would I be better off purchasing a combine with a 145 engine in it that bolts in? Found one a state over for 1000 that runs...

How any hours a year and how hard do you really use the old girl? Put new standard bearings in and run it.
How many old tractors and engines are out there that has not been touched in thousands of hours that are still pulling there weight.
Yes, in a perfect world it should be turned / replaced. Save your money for another project.
Just my opinion.

Any info on rod cap torque values
Back to top
View user's profile
Post new topic    Yesterday's Tractors Forum Index -> John Deere All times are GMT - 8 Hours
Goto page Previous  1, 2
Page 2 of 2

Jump to:  

We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters