Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

New TO 20 owner

Goto page Previous  1, 2

 
Post new topic    
View previous topic :: View next topic  
Author Message
ajhbike
Regular


Joined: 14 Mar 2017
Posts: 283


Report to Moderator

PostPosted: Tue Jun 11, 2019 7:27 am    Post subject: Re: New TO 20 owner Reply to specific post Reply with quote

okay thanks. It is a grease fitting.

So my PTO shaft has an overrunning clutch...it is different than my other... There must be a pin or something holding it on.

I have to admit that I haven't had much time to look at the TO closely. Picked it up with a 12 ft trailer...blew out the trailer tire in White Plains, NY. Shuttled the tractor home on a UHAUL transporter, spare trailer tire had a different lug pattern, Troopers had it towed, blah, blah blah. Quite a day. Good news is the trailer didn't flip and the tractor started for the UHAUL and at home.

Thank you for the offer...let me check this out a little closer tonight tonight
 
Back to top
View user's profile
ajhbike
Regular


Joined: 14 Mar 2017
Posts: 283


Report to Moderator

PostPosted: Tue Jun 11, 2019 7:28 am    Post subject: Re: New TO 20 owner Reply to specific post Reply with quote

Got it, will check it out tonight, thanks
 
Back to top
View user's profile
John Deere D
Tractor Guru


Joined: 14 Jun 2011
Posts: 3668


Report to Moderator

PostPosted: Tue Jun 11, 2019 7:46 am    Post subject: Re: New TO 20 owner Reply to specific post Reply with quote

Bob...Owner Operator Ferguson & Ford 2-N



 
Back to top
View user's profile
ajhbike
Regular


Joined: 14 Mar 2017
Posts: 283


Report to Moderator

PostPosted: Tue Jun 11, 2019 8:00 am    Post subject: Re: New TO 20 owner Reply to specific post Reply with quote

I understand....the ORC fits over the tractor shaft and the visible shaft with the splines is a part of the ORC.

But there must be a pin holding the ORC on the original shaft, no?
 
Back to top
View user's profile
Go4Broke2
Regular


Joined: 29 Mar 2015
Posts: 38


Report to Moderator

PostPosted: Tue Jun 11, 2019 8:35 am    Post subject: Re: New TO 20 owner Reply to specific post Reply with quote

You should have a grease zerk on one side and an
Allen screw directly opposite the zerk on the other
side of the orc. Remove both. Use a punch and
drive out the roll pin that holds the orc on. Be careful
the punch isn?t so large that it messes up the
threads, but not so small it goes inside the roll pin. If
it does it might be hard to remove. The roll pin is
5/16 x 1 1/4 long. I bought my last one at Napa for a
buck.
 
Back to top
View user's profile
ajhbike
Regular


Joined: 14 Mar 2017
Posts: 283


Report to Moderator

PostPosted: Tue Jun 11, 2019 10:39 am    Post subject: Re: New TO 20 owner Reply to specific post Reply with quote

okay, thank you. will advise
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Harry Ferguson All times are GMT - 8 Hours
Goto page Previous  1, 2
Page 2 of 2

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters