Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Farmall governor


 
Post new topic    
View previous topic :: View next topic  
Author Message
Ohio-H
New User


Joined: 19 Jun 2011
Posts: 18


Report to Moderator

PostPosted: Wed Jul 10, 2019 7:58 pm    Post subject: Farmall governor Reply to specific post Reply with quote

What would happen if i replaced the governor spring with an adjustable rod with small heim joints on each end....Just curious, Thanks....H
 
Back to top
View user's profile
MikeJM
Long Time User


Joined: 09 Jul 2014
Posts: 649
Location: New Jersey

Report to Moderator

PostPosted: Thu Jul 11, 2019 6:46 am    Post subject: Re: Farmall governor Reply to specific post Reply with quote

That would effectively eliminate the governor.
At that point just hook the throttle right to the carb, I do not recommend doing such a thing.
 
Back to top
View user's profile
Ohio-H
New User


Joined: 19 Jun 2011
Posts: 18


Report to Moderator

PostPosted: Sat Jul 13, 2019 8:27 am    Post subject: Re: Farmall governor Reply to specific post Reply with quote

My "H" with C-169 was built to run around 2000, 2100 rpm's. cant hardly get it to rev up to
factory specs, even with a new "heavy" spring and what i thought was an adjusted governor.
Any suggestions? Would replacing the spring with the rod do this? I ask because the piece i
describe was in one of those "Dennys" magic pulling governor kits that was bought for me,
and it had no instructions for the extra parts....Thanks; Joe
 
Back to top
View user's profile
460anger
Regular


Joined: 01 Nov 2007
Posts: 378


Report to Moderator

PostPosted: Sat Aug 10, 2019 3:25 am    Post subject: Re: Farmall governor Reply to specific post Reply with quote

I have always wondered y you guys that are trying to make all this horse power and rpms mess with a governor at all ?? my thoughts get rid of it!!
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Pulling All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters