Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

1600 clutch


 
Post new topic    
View previous topic :: View next topic  
Author Message
rrlund
Tractor Guru


Joined: 21 Dec 2006
Posts: 41493


Report to Moderator

PostPosted: Thu Jul 11, 2019 3:29 pm    Post subject: 1600 clutch Reply to specific post Reply with quote

Could it be that simple?

Not long ago,somebody posted about a clutch not releasing when it got heated up. I believe it was on a 1600. I didn't reply because I was having the same trouble and hadn't found the problem. When I was hauling round bales home early this spring and unloading with my 1600 loader tractor,it was giving me fits. I had to pull it in to under drive to shift between gears and direct then idle it all the way down to get it in gear from neutral. I adjusted the pedal free travel by adjusting the rod. It helped a little bit,but not much and not long.

I've been hauling round bales home this week and using it to unload and stack them in the barn. It was hanging up and grinding gears so bad that I was seriously considering putting the loader on a different tractor until I could pull the engine and change the clutch and pressure plate.

I was putting oil in it this morning and noticed that it looked like the cast cowl had been moving where it bolts to the tub. I got a wrench and those half inch bolts were loose as a goose. I tightened them up and used it all day unloading and stacking. It works great. I think the whole casting was moving when I pushed the pedal down,so adjusting it wasn't doing any good. It was just shifting out of whack then moving back again when I let the pedal up.

The odd things that happen!
 
Back to top
View user's profile
r.w.b.
Tractor Expert


Joined: 04 Jul 2016
Posts: 1695


Report to Moderator

PostPosted: Thu Jul 11, 2019 3:54 pm    Post subject: Re: 1600 clutch Reply to specific post Reply with quote

My 1650 let the plate the bell housing bend down,that thin plate supports maybe 150 pounds plus hanging way back there its a wonder it didnt break.
My fix i took nuts off the engine mount bolts ,removed drive chain and pto shaft,jacked rear of engine up.i cut a 6"x6"x1" thick piece of old bias ply truck tire tread and put it under the
Hydra power and frame, let engine back down it was just a hair too high but i went ahead n put er back together.was so much smoother clutch was great too.and by second daybthe gear teeth on both sprockets were flush.i since have done that to 5 other 1650 and 1655s.owners were very happy
 
Back to top
View user's profile
carolina oliver
Regular


Joined: 22 Dec 2004
Posts: 64


Report to Moderator

PostPosted: Thu Jul 11, 2019 4:47 pm    Post subject: Re: 1600 clutch Reply to specific post Reply with quote

I'm certainly not the expert here, but lots of us have done this to keep the sprockets lined up: apparently was done in factory on some although not on my 1655 or 2-70: Drill a 5/8 or 1/2 in. hole in bottom of tub under back side of 2 speed or 3 speed as you have. Run a bolt w/ locking nut up thru your threaded whole, raise 2-3 speed up so sprockets align better.. helped on mine.
 
Back to top
View user's profile
jim ball
Regular


Joined: 14 Apr 2010
Posts: 71


Report to Moderator

PostPosted: Sat Jul 13, 2019 3:20 am    Post subject: Re: 1600 clutch Reply to specific post Reply with quote

i have 1650 & am getting ready to do a clutch & rear main seal. what is "cast cowl' ? thanks
 
Back to top
View user's profile
rrlund
Tractor Guru


Joined: 21 Dec 2006
Posts: 41493


Report to Moderator

PostPosted: Sat Jul 13, 2019 5:06 am    Post subject: Re: 1600 clutch Reply to specific post Reply with quote

My term for lack of a better name for the lower half of the dash that the clutch and brake pedals are mounted to. The part where the serial tag is riveted to.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters