Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Sherman combo


 
Post new topic    
View previous topic :: View next topic  
Author Message
Paul Humphrey
New User


Joined: 10 Feb 2017
Posts: 7
Location: Boonville MO

Report to Moderator

PostPosted: Tue Aug 13, 2019 3:21 pm    Post subject: Sherman combo Reply to specific post Reply with quote


I just bought an 8N that has a Sherman combo that won't go into the high side.Apparently the shifter mechanism is worn enough that it won't slip all the way back to engage.Anyone know if I can get at the shifter by pulling the top off the transmission housing instead of splitting the tractor?
 
Back to top
View user's profile
Den N Ms
Tractor Guru


Joined: 20 Feb 2007
Posts: 5930


Report to Moderator

PostPosted: Tue Aug 13, 2019 3:34 pm    Post subject: Re: Sherman combo Reply to specific post Reply with quote

Paul,Yes you can get at it by removing the steering cover of the transmission.But if you need to disassemble more than the top cover of the Sherman for repair it will need to be split.I would split it in the first place as that is just about as easy as removing the dash and box.
 
Back to top
View user's profile
Paul Humphrey
New User


Joined: 10 Feb 2017
Posts: 7
Location: Boonville MO

Report to Moderator

PostPosted: Tue Aug 13, 2019 3:58 pm    Post subject: Re: Sherman combo Reply to specific post Reply with quote

Thanks Den...............I thought that would be the case,but wasn't sure.I've had a lot of experience with 9Ns and 2Ns,but this is my first 8N.

Thanks again

Paul
 
Back to top
View user's profile
Mike Groom
Long Time User


Joined: 07 Mar 2008
Posts: 1300


Report to Moderator

PostPosted: Tue Aug 13, 2019 4:07 pm    Post subject: Re: Sherman combo Reply to specific post Reply with quote

Paul,I just split a Jubilee to fix the Combo Sherman that would not shift,turns out it was a worn ball bearing in the shifter mechanism,I think it was a 5/16 if I remember right,you should just split the tractor,it was only a half a day job from start to finish.
 
Back to top
View user's profile
Kirk-NJ
Tractor Guru


Joined: 10 Dec 2006
Posts: 5212


Report to Moderator

PostPosted: Tue Aug 13, 2019 11:32 pm    Post subject: Re: Sherman combo Reply to specific post Reply with quote

I have removed the top cover from the sherman thru the steering box hole once. It was a fight. As others have said a split will be easier.
 
Back to top
View user's profile
Kirk-NJ
Tractor Guru


Joined: 10 Dec 2006
Posts: 5212


Report to Moderator

PostPosted: Tue Aug 13, 2019 11:36 pm    Post subject: Re: Sherman combo Reply to specific post Reply with quote

Here is a combo I took out of a 640 basically same as 8n
sherman removal link

 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Ford 9N, 2N, 8N All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters