Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Front wheel conversion on farmall 450


 
Post new topic    
View previous topic :: View next topic  
Author Message
dirt_digger
New User


Joined: 09 Aug 2019
Posts: 1


Report to Moderator

PostPosted: Fri Aug 09, 2019 10:38 pm    Post subject: Front wheel conversion on farmall 450 Reply to specific post Reply with quote

Hello new here, I ve been wanting to convert to car style front hubs, specifically Chevy 5 hole on my farmall 450 factory wide front. Not sure where to begin, and can t find info on it really anywhere. I know it s been done as I ve seen plenty of pictures on pullers. Any information would be greatly appreciated as to what hubs and bearings etc are used. Thanks a lot.
 
Back to top
View user's profile
Gary Mitchell
Tractor Expert


Joined: 05 Jun 2000
Posts: 1667
Location: St Clair Co. Missouri

Report to Moderator

PostPosted: Sat Aug 10, 2019 9:19 am    Post subject: Re: Front wheel conversion on farmall 450 Reply to specific post Reply with quote

When I do that I measure the spindle size of the tractor and race OD size of a hub that will accommodate the wheel I want to use and buy bearing/race sets accordingly. gm
 
Back to top
View user's profile AIM Address
Sweeper
Regular


Joined: 13 Sep 2010
Posts: 32


Report to Moderator

PostPosted: Tue Aug 13, 2019 5:18 am    Post subject: Re: Front wheel conversion on farmall 450 Reply to specific post Reply with quote

Remake front end and use a hub from the rear of a front wheel drive GM car. You can find any wheel you want.
 
Back to top
View user's profile
VicS
Tractor Guru


Joined: 12 Mar 2010
Posts: 4846


Report to Moderator

PostPosted: Fri Aug 16, 2019 5:45 am    Post subject: Re: Front wheel conversion on farmall 450 Reply to specific post Reply with quote

We go one step farther, just buy sealed ball bearings. No mess no fuss. Know not as strong, but your not going to drive it that many miles.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Pulling All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters