Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Bleeding a 2630 Fuel System


 
Post new topic    
View previous topic :: View next topic  
Author Message
Ohiohills
Regular


Joined: 02 Nov 2006
Posts: 85


Report to Moderator

PostPosted: Sun Sep 01, 2019 7:19 pm    Post subject: Bleeding a 2630 Fuel System Reply to specific post Reply with quote

I'm in need of some rather urgent help! I foolishly ran my 2630 out of fuel yesterday ... just made it to the fuel storage tank, but not soon enough. Sad Now, of course, it won't restart, so I assume I must purge air from the fuel system. Never done this before so I'm wondering if anyone is willing to scan and post the relevant pages from a 2630 Operator Manual that detail the specific steps for bleeding the fuel system?

PS: Yes, I have now ordered a 2630 Operator Manual off eBay, but it won't ship until Tuesday and probably won't get here until a week from now!
 
Back to top
View user's profile
Tx Jim
Tractor Guru


Joined: 14 Feb 1999
Posts: 31833


Report to Moderator

PostPosted: Mon Sep 02, 2019 1:56 am    Post subject: Re: Bleeding a 2630 Fuel System Reply to specific post Reply with quote


Open bleeder screw on fuel filter housing,pump lever on fuel transfer pump until air free fuel appears, tighten bleed screw pull throttle down 1/2 way & try to start engine. If no resistance is felt when pumping fuel pump lever rotate engine slightly to get camshaft lobe to move from pressing on internal lever on FP. It's possible you might have to loosen fuel line that supplies inj pump to purge air. This will be determined by how many times you attempted to start engine after it ran out of fuel. Some inj pumps have bleeder screws one can loosen but I can't remember if 2630 IP has this screw or not .
 
Back to top
View user's profile
Jim.ME
Tractor Guru


Joined: 02 Mar 2018
Posts: 7305


Report to Moderator

PostPosted: Mon Sep 02, 2019 3:20 am    Post subject: Re: Bleeding a 2630 Fuel System Reply to specific post Reply with quote

You may need to add another step after completing Tx Jim's steps if it doesn't start.

You may need to loosen the fuel injector lines, from the injector pump, at the injector ends. With them loose, crank the engine until you get fuel coming out of them, then tighten.
 
Back to top
View user's profile
JDEM
Tractor Expert


Joined: 18 Mar 2016
Posts: 2634


Report to Moderator

PostPosted: Mon Sep 02, 2019 5:18 am    Post subject: Re: Bleeding a 2630 Fuel System Reply to specific post Reply with quote

The Standadyne injection pump is self-bleeding so there is on specific-built bleeder anywhere. If you want to speed up the bleeding process, just crack some lines loose. That and any bleeder screw or screws you might have on the filter.
 
Back to top
View user's profile
Resting Relics 1
Long Time User


Joined: 15 Nov 2007
Posts: 678


Report to Moderator

PostPosted: Mon Sep 02, 2019 8:52 am    Post subject: Re: Bleeding a 2630 Fuel System Reply to specific post Reply with quote

Ohiohills,
Gotta agree with Jim on this one. Best method I've found to bleed these tractors is to open the bleeder on the filter and use the hand pump to purge the air. Then crack open each injector line at the injectors and crank it over till you see fuel. As each line shows fuel tighten it up and crank until all show fuel. It'll start then. Good Luck!
John
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> John Deere All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters