Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

AC G Model Questions


 
Post new topic    
View previous topic :: View next topic  
Author Message
C.Amick
Regular


Joined: 30 Jan 2013
Posts: 476


Report to Moderator

PostPosted: Tue Sep 10, 2019 5:15 pm    Post subject: AC G Model Questions Reply to specific post Reply with quote

What size are the rear tires on a G Model? How much do a set of G Model plows typically sell for?
 
Back to top
View user's profile
ramblineagle
Regular


Joined: 13 Apr 2001
Posts: 314


Report to Moderator

PostPosted: Tue Sep 10, 2019 6:10 pm    Post subject: Re: AC G Model Questions Reply to specific post Reply with quote


G rear tire size are 7.2 x 30 some have 8.5 x 30" just depends on what the owner wants. A G plow is hard to find, selling price is what the seller and buyer agree on. have seen them sell for $75.00 on up too over $200.00.
 
Back to top
View user's profile
Mike(NEOhio)
Tractor Guru


Joined: 12 May 2013
Posts: 4607
Location: Geauga County, Ohio

Report to Moderator

PostPosted: Wed Sep 11, 2019 4:33 am    Post subject: Re: AC G Model Questions Reply to specific post Reply with quote

Are you looking for the left-right hand or just a single. I have a couple here. The G OP manual recommends NOT adding wheel weights or liquid ballast so I would stay away from oversized tires. The axle shafts were a weak point and it was common to break a shaft when the plow hits something. I broke one just using the brakes to steer while mowing with a 4 foot Mott.
 
Back to top
View user's profile
C.Amick
Regular


Joined: 30 Jan 2013
Posts: 476


Report to Moderator

PostPosted: Wed Sep 11, 2019 5:02 pm    Post subject: Re: AC G Model Questions Reply to specific post Reply with quote

Did you weld the axle back together or find a used one? There is a G Model coming up for auction that has plows with it. Only problem is that the tractor is disassembled. Motor is assembled. I am trying to figure out how much it is worth. I don't know the condition of the tires, so I am trying to price tires.
 
Back to top
View user's profile
C.Amick
Regular


Joined: 30 Jan 2013
Posts: 476


Report to Moderator

PostPosted: Wed Sep 11, 2019 5:12 pm    Post subject: Re: AC G Model Questions Reply to specific post Reply with quote

Can you find parts for the engine? Is it a Hercules Engine? For some reason I'm thinking that it is not a Continental.
 
Back to top
View user's profile
VACLee
Long Time User


Joined: 03 Jul 2007
Posts: 753
Location: Gibsonville, NC

Report to Moderator

PostPosted: Wed Sep 11, 2019 5:32 pm    Post subject: Re: AC G Model Questions Reply to specific post Reply with quote

Continental N62. Same basic engine as the MH Pony. The blocks are different due to starter arrangement and will not interchange. The heads have different size plugs (14mm vs 18mm) but they will interchange. Parts are pretty easy to find. Axles can be welded but sometimes can be hard to get them straight and smooth enough for the seal not to leak. All that I have had apart the break was always right at the seal location. May or may not have the low gear option. Factory hydraulics would be a plus. Original size rears were 6x30 with 7.2x30 being the replacement size. Definitely would not recommend going any larger as was mentioned above. Front weight is also a desirable option and needed if no front implement is mounted. Bare tractor front axle weight is probably under 100 lbs. Lee
 
Back to top
View user's profile
golfcartman
Regular


Joined: 05 Jan 2010
Posts: 482


Report to Moderator

PostPosted: Wed Sep 11, 2019 6:01 pm    Post subject: Re: AC G Model Questions Reply to specific post Reply with quote

I have restored 4 of these tractors in the past 10-12 years. Just finished one a couple weeks ago. The parts are very expensive, new or used. Rusty Acre tractor parts is prolly the cheapest but have limited parts. Lots of parts on eBay but high priced. The engine is a Continential n62. The Pistons won't come out the top with the rod attached. The rod cap is larger than the Pistons. They are a pain to put new rings in. Here is the one I just finished.







 
Back to top
View user's profile
Mike(NEOhio)
Tractor Guru


Joined: 12 May 2013
Posts: 4607
Location: Geauga County, Ohio

Report to Moderator

PostPosted: Thu Sep 12, 2019 3:26 am    Post subject: Re: AC G Model Questions Reply to specific post Reply with quote

My axle broke right at the splined end in the differential. Didn't make any noise, just stopped moving. I was concerned that there could be chunks in the gears so I took the whole rear end off and pulled the diff to make sure it was clean. I had a spare tractor that came along in the deal so I switched one from it. Hardest part was getting the brake drums off the shaft.
 
Back to top
View user's profile
C.Amick
Regular


Joined: 30 Jan 2013
Posts: 476


Report to Moderator

PostPosted: Thu Sep 12, 2019 4:37 am    Post subject: Re: AC G Model Questions Reply to specific post Reply with quote

Looks great.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters