Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

DB 1200 hydraulics


 
Post new topic    
View previous topic :: View next topic  
Author Message
dieselherb
New User


Joined: 19 Mar 2018
Posts: 13


Report to Moderator

PostPosted: Wed Oct 09, 2019 4:31 am    Post subject: DB 1200 hydraulics Reply to specific post Reply with quote

I have a DB 1200 the lift arms go up every time the engine is started, the controls do nothing. It has been sitting for years. I removed the caps over the valves near the hydrant but how do you get the valves out? Is there a place I can push them up?
 
Back to top
View user's profile
RGMartin
Tractor Expert


Joined: 14 Jan 2011
Posts: 3445


Report to Moderator

PostPosted: Wed Oct 09, 2019 7:02 am    Post subject: Re: DB 1200 hydraulics Reply to specific post Reply with quote

It goes up then you hear the engine laboring?

When you shut it off with the arms up, do they go down if you let the lever down?
 
Back to top
View user's profile
dieselherb
New User


Joined: 19 Mar 2018
Posts: 13


Report to Moderator

PostPosted: Wed Oct 09, 2019 8:12 am    Post subject: Re: DB 1200 hydraulics Reply to specific post Reply with quote

RGMartin wrote:
(quoted from post at 08:02:28 10/09/19) It goes up then you hear the engine laboring?

When you shut it off with the arms up, do they go down if you let the lever down?




Arms go up but the engine doesn't labor doesn't matter where the control lever is doesn't affect up or down and when you shut motor off it slowly goes down
 
Back to top
View user's profile
RGMartin
Tractor Expert


Joined: 14 Jan 2011
Posts: 3445


Report to Moderator

PostPosted: Wed Oct 09, 2019 12:34 pm    Post subject: Re: DB 1200 hydraulics Reply to specific post Reply with quote

The hold and bypass valves(the ones you have the caps off of) can be removed by wedging a wooden dowel rod down into them after you pull the springs out.

I don't think that they are the problem though. Probably have to pull the valve body out to get to the "spool" or "latching" valve.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters