Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Hydraulic oil

Goto page Previous  1, 2

 
Post new topic    
View previous topic :: View next topic  
Author Message
kyford8n
Regular


Joined: 03 Nov 2017
Posts: 49
Location: Fancy Farm, KY

Report to Moderator

PostPosted: Fri Dec 13, 2019 7:33 am    Post subject: Re: Hydraulic oil Reply to specific post Reply with quote

Hey guys,

I changed my fluids several months back using UTF. I have a slight leak at my weep hole area and need to add more fluid. Would it hurt anything to add the SAE 90 to the UTF? Just looking to try to slow up the leak a little and wasn't sure if mixing them would hurt anything.
 
Back to top
View user's profile
TheOldHokie
Tractor Guru


Joined: 08 Apr 2005
Posts: 10722
Location: Myersville, MD

Report to Moderator

PostPosted: Fri Dec 13, 2019 9:43 am    Post subject: Re: Hydraulic oil Reply to specific post Reply with quote

kyford8n wrote:
(quoted from post at 11:33:35 12/13/19) Hey guys,

I changed my fluids several months back using UTF. I have a slight leak at my weep hole area and need to add more fluid. Would it hurt anything to add the SAE 90 to the UTF? Just looking to try to slow up the leak a little and wasn't sure if mixing them would hurt anything.


Mixing won't hurt anything but unless you are adding multiple gallons it won't slow the leak.

TOH
 
Back to top
View user's profile
kyford8n
Regular


Joined: 03 Nov 2017
Posts: 49
Location: Fancy Farm, KY

Report to Moderator

PostPosted: Fri Dec 13, 2019 10:03 am    Post subject: Re: Hydraulic oil Reply to specific post Reply with quote

Thanks TOH,

How bad of a job is it for a rookie to replace the seal?
 
Back to top
View user's profile
TheOldHokie
Tractor Guru


Joined: 08 Apr 2005
Posts: 10722
Location: Myersville, MD

Report to Moderator

PostPosted: Fri Dec 13, 2019 10:28 am    Post subject: Re: Hydraulic oil Reply to specific post Reply with quote

kyford8n wrote:
(quoted from post at 14:03:48 12/13/19) Thanks TOH,

How bad of a job is it for a rookie to replace the seal?


You have to split and rejoin the tractor behind the engine which will take you a day. Pretty easy in a shop with a floor jack and concrete floor. Not so nice or easy outside and/or on the ground. Other than that nothing difficult about the seal itself. Good time to consider clutch service while you are in there especially given the seal is leaking....

TOH
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Ford 9N, 2N, 8N All times are GMT - 8 Hours
Goto page Previous  1, 2
Page 2 of 2

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters