Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

tooth angle on a 806


 
Post new topic    
View previous topic :: View next topic  
Author Message
fastfarmall
Tractor Guru


Joined: 05 Feb 2015
Posts: 4281


Report to Moderator

PostPosted: Mon Jan 13, 2020 3:41 pm    Post subject: tooth angle on a 806 Reply to specific post Reply with quote

What tooth angle did they use on a 806-1206 final drive? Never heard of a 806 final drive failure around here, but i knew that two 1206 Row crops that failed, but they had the wick turned up live the TV would say, the one was run bye a kid that had polio in his right arm, or else it was cut off and he wouldn't or couldn't raise the digger on the corner's, looked at the tractor it had scale on the exhaust manifold like i never seen before!!
 
Back to top
View user's profile
caterpillar guy
Tractor Guru


Joined: 24 Jun 2007
Posts: 5336


Report to Moderator

PostPosted: Tue Jan 14, 2020 4:52 am    Post subject: Re: tooth angle on a 806 Reply to specific post Reply with quote

I've heard of the brake shafts breaking on a few 1206's no other problems though and you had to jump on the pedal for that to happen. The Bull gears in both of them are huge compared to earlier models.
 
Back to top
View user's profile
pete 23
Tractor Guru


Joined: 10 Sep 2009
Posts: 6927


Report to Moderator

PostPosted: Tue Jan 14, 2020 8:20 am    Post subject: Re: tooth angle on a 806 Reply to specific post Reply with quote

I am 99% sure the bull gears are 25 degree but do know the transmission gears were still the old industry standards 20 degree teeth.

Midway into the 56 series all transmission and pto drive gears were changed to 25 degree.

Failures started to occur in ring and pinion on 1206 models and then into bull pinion and axle bearings later around here.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters