Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

super 88 exhaust manifold


 
Post new topic    
View previous topic :: View next topic  
Author Message
Fatjay
Long Time User


Joined: 03 Apr 2015
Posts: 577
Location: Eastern PA

Report to Moderator

PostPosted: Mon Jan 13, 2020 6:17 pm    Post subject: super 88 exhaust manifold Reply to specific post Reply with quote

I have a 77 industiral with a super 88 motor. The exhaust manifold is all but gone. Taking thte exhaust manifold off will also remove the intake manifold. If I'm taking that off I may as well replace it as well. I will also need all new gaskets for exhaust and intake.

So the question is, can I still get the intake manifold, exhaust manifold, and gaskets for them?

Follow up question: Those rods coming out of the engine that have nuts holding the intake and exhaust manifolds on, are they threaded into the engine, as in threads on both ends?
 
Back to top
View user's profile
J. Schwiebert
Tractor Guru


Joined: 27 Sep 2013
Posts: 4969


Report to Moderator

PostPosted: Tue Jan 14, 2020 6:28 am    Post subject: Re: super 88 exhaust manifold Reply to specific post Reply with quote

The exhaust manifold is available BUT the part number will sub to a manifold that is improved and fits another later tractor. On the intake I have no idea as I never had to look one up. Gaskets are no problem. The attaching studs are threaded on both ends. More questions?
 
Back to top
View user's profile
Dblair
Tractor Expert


Joined: 07 Nov 2007
Posts: 2830


Report to Moderator

PostPosted: Tue Jan 14, 2020 8:18 am    Post subject: Re: super 88 exhaust manifold Reply to specific post Reply with quote

Korves Oliver has them
 
Back to top
View user's profile
Fatjay
Long Time User


Joined: 03 Apr 2015
Posts: 577
Location: Eastern PA

Report to Moderator

PostPosted: Tue Jan 14, 2020 6:49 pm    Post subject: Re: super 88 exhaust manifold Reply to specific post Reply with quote


Thanks I think I found it at steiners. I had to go look at the intake because it showed only 3 ports but apparently that's how it is and it splits it to the 6 cylinders inside.

I was worried about the shafts being double threaded because Im not sure the nuts are going to come off nicely and I didn't want to break something off in the engine that I would have to take the engine apart for.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters