Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Long 560 clutch install and gauge block


 
Post new topic    
View previous topic :: View next topic  
Author Message
LoMo88
New User


Joined: 12 Mar 2020
Posts: 2


Report to Moderator

PostPosted: Thu Mar 12, 2020 6:30 pm    Post subject: Long 560 clutch install and gauge block Reply to specific post Reply with quote

In the manual for setting up the clutch fingers for a Long 560/UTB 550 it talks about using a gauge block tool. The block has a part number but haven't been able to find it. I could make one if i knew the dimensions. Does anyone know anything about this? So far, the places that we've contacted and the internet searching we've done, it seems like no one has ever done a clutch job on one of these. Any help is appreciated. Thanks

 
Back to top
View user's profile
Traditional Farmer
Tractor Guru


Joined: 26 Apr 2007
Posts: 20018


Report to Moderator

PostPosted: Fri Mar 13, 2020 4:02 am    Post subject: Re: Long 560 clutch install and gauge block Reply to specific post Reply with quote

We did the clutch on my Oliver 1365 same basic clutch,but bought it in a package already set up as setting them up isn't an amateur hour job.Take it to an AGCO or maybe a NH dealer they should have someone that can do it.
 
Back to top
View user's profile
SkipperII
Regular


Joined: 01 Dec 2017
Posts: 449


Report to Moderator

PostPosted: Fri Mar 13, 2020 1:15 pm    Post subject: Re: Long 560 clutch install and gauge block Reply to specific post Reply with quote

If you are just replacing the disc, and have not messed with the adjustment bolts, it should be pretty close. The important part is that they are even, you should be able to measure with a depth gauge, and adjust to the furthest out. Main clutch to main clutch, and pto to pto. If you are installing a replacement unit, they are generally preadjusted. Just as a point of reference; The Fordson Majors PTO levers set 5/8" lower than the main clutch levers, with the clutch mounted to the flywheel. Hope this helps.
 
Back to top
View user's profile
LoMo88
New User


Joined: 12 Mar 2020
Posts: 2


Report to Moderator

PostPosted: Sat Mar 14, 2020 6:06 pm    Post subject: Re: Long 560 clutch install and gauge block Reply to specific post Reply with quote

Thank you for the suggestions
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Lesser Known Classics All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters